OPERATION

IMPORTANT SAFETY INSTRUCTIONS

WARNING

To reduce the risk of SEVERE INJURY or DEATH:

1.

READ AND FOLLOW ALL WARNINGS AND INSTRUCTIONS.

9. If one control (force or travel limits) is adjusted, the other

2.

ALWAYS keep remote controls out of reach of children.

 

control may also need adjustment.

 

NEVER permit children to operate or play with garage door

10.

After ANY adjustments are made, the safety reversal system

 

control push buttons or remote controls.

 

MUST be tested.

3.

ONLY activate garage door when it can be seen clearly, it is

11.

Safety reversal system MUST be tested every month.

 

properly adjusted, and there are no obstructions to door

 

Garage door MUST reverse on contact with 1-1/2" high

 

travel.

 

(3.8 cm) high object (or a 2x4 laid flat) on the floor.

4.

ALWAYS keep garage door in sight until completely closed.

12.

ALWAYS KEEP GARAGE DOOR PROPERLY BALANCED (see

 

NO ONE SHOULD CROSS THE PATH OF THE MOVING

 

page 3). An improperly balanced door may not reverse

 

DOOR.

 

when required and could result in SEVERE INJURY or

5.

NO ONE SHOULD GO UNDER A STOPPED, PARTIALLY OPEN

 

DEATH.

 

DOOR.

13.

ALL repairs to cables, spring assemblies and other

6.

If possible, use emergency release handle to disengage

 

hardware, ALL of which are under EXTREME tension, MUST

 

trolley ONLY when garage door is CLOSED. Weak or broken

 

be made by a trained door systems technician.

 

springs or unbalanced door could result in an open door

14.

ALWAYS disconnect electric power to garage door opener

 

falling rapidly and/or unexpectedly.

 

BEFORE making ANY repairs or removing covers.

7.

NEVER use emergency release handle unless garage doorway

15. SAVE THESE INSTRUCTIONS.

 

is clear of persons and obstructions.

 

 

 

8.NEVER use handle to pull garage door open or closed. If rope knot becomes untied, you could fall.

Using Your Garage Door Opener

6. If obstructed while opening, the door will stop.

Your Security✚® opener and hand-held remote control

7. If fully open, the door will not close when the beam is

broken. The sensor has no effect in the opening cycle.

have been factory-set to a matching code which changes

If the sensor is not installed, or is misaligned, the door

with each use, randomly accessing over 100 billion new

won’t close from a hand-held remote. However, you can

codes. Your opener will operate with up to eight Security✚®

close the door with the Door Control, the Outside Keylock,

remote controls and one Security✚® Keyless Entry System.

or Keyless Entry, if you activate them until down travel is

If you purchase a new remote, or if you wish to deactivate

complete. If you release them too soon, the door will

any remote, follow the instructions in the Programming

reverse.

section.

The opener lights will turn on under the following

Activate your opener with any of the following:

conditions: when the opener is initially plugged in; when

•

The hand-held Remote Control: Hold the large push

power is restored after interruption; when the opener is

 

button down until the door starts to move.

activated.

•

The wall-mounted Door Control: Hold the push button or

They will turn off automatically after 4-1/2 minutes or

 

bar down until the door starts to move.

 

provide constant light when the Light feature on the

•

The Keyless Entry (See Accessories): If provided with

Multi-Function Door Control is activated. Bulb size is A19.

 

your garage door opener, it must be programmed before

Bulb power is 100 watts maximum.

 

use. See Programming.

Security✚ ®light feature: Lights will also turn on when

When the opener is activated (with the safety reversing

someone walks through the open garage door. With a

sensor correctly installed and aligned)

Multi-Function Door Control, this feature may be turned off

1. If open, the door will close. If closed, it will open.

as follows: With the opener lights off, press and hold the

2. If closing, the door will reverse.

light button for 10 seconds, until the light goes on, then off

3. If opening, the door will stop.

again. To restore this feature, start with the opener lights

on, then press and hold the light button for 10 seconds

4. If the door has been stopped in a partially open position,

until the light goes off, then on again.

it will close.

 

5.If obstructed while closing, the door will reverse. If the obstruction interrupts the sensor beam, the opener lights will blink for five seconds.

26