Manuals / Brands / Household Appliance / Garage Door Opener / Chamberlain / Household Appliance / Garage Door Opener

Chamberlain 3575S Rail Assembly Parts, Installation Parts, NO, NO, KEY, PART, KEY PART, DESCRIPTION, REPAIR PARTS, NO. NO. DESCRIPTION

1 40

Download 40 pages, 2.63 Mb

REPAIR PARTS

Rail Assembly Parts

1

5

3

4

2

6

Installation Parts

5

4 2 1

KEY PART

NO. NO. DESCRIPTION

14A1008 Master link kit

241A4813 Chain pulley bracket

341A3489 Complete trolley assembly

41707LM One-piece rail for 7' (2.1 m) door

541D3484 Full chain assembly

6	83A11-2	Rail grease
	NOT SHOWN
	1708LM	One-piece rail for 8' (2.4 m)
		door
	1710LM	One-piece rail for 10' (3 m)
		door

LOCK LIGHT

6

NOTICE

9

ONLY

MOUNT

CEILING

UP

12

	3	KEY	PART
		NO.	NO.	DESCRIPTION
	7	1	398LM	Smart Control Panel™
	7	2	373P	3-button remote
	8	2	373P	3-button remote
	8	3	10A19	3V2016 lithium battery: led and opener
		4	10A33	3V2450 lithium battery: proximity switch
	11	5	29C151	Remote control visor clip
	11	6	41A2828	Emergency release rope & handle assembly.
		7	41B4494-1	2-Conductor bell wire, white & white/red
	10	8	41A5047-1	Door bracket w/clevis pin & fastener
		9	41A4353-1	Header bracket w/clevis pin & fastener
		10	41A5034	Safety sensor kit (receiving and sending
				eyes) with 3' (.9 m) 2-conductor bell wire
	13	11	178B34	Straight door arm section
	13	12	178B35	Curved door arm section
		13	41A5266-1	Safety sensor brackets (2)
				NOT SHOWN
			41A2770-5	Installation hardware bag
				(includes hardware listed on page 5).
			114A3615	Owner's manual
			114A3615SP	Owner’s manual - Spanish

35

Contents

For Residential Use Only Introduction2-5 Assembly6-7 Installation7-22 Adjustment23-25 Operation26-32 Preparing your garage door Tools needed Planning Carton Inventory Attach the T-Railto the Motor Unit Attach the Chain Spreader Tighten the Chain Determine the Header Bracket Location Install the Header Bracket Attach the Rail to the Header Bracket Position the Opener Hang the Opener Install the Door Control Install the Light Attach the Emergency Release Rope and Handle Electrical Requirements Install The Protector System® INSTALLING THE BRACKETS Garage door track installation (preferred) (Figure 1): Wall installation (Figures 2 & 3): Floor installation (Figure 4): MOUNTING AND WIRING THE SAFETY REVERSING SENSORS TROUBLESHOOTING THE SAFETY REVERSING ALIGNING THE SAFETY REVERSING SENSORS Fasten the Door Bracket ONE-PIECEDOORS Metal Doors: Connect Door Arm to Trolley ALL ONE-PIECEDOORS 1. Assemble the door arm, Figure 4: 2. Adjustment procedures, Figure 5: • Open door adjustment: decrease UP travel limit 3. Connect the door arm to the trolley: Adjust the UP and DOWN Travel Limits Adjust the Force Test the Safety Reversal System Test The Protector System® Using Your Garage Door Opener Using the Wall-MountedDoor Control Using the Remote Control The Remote Control Batteries Troubleshooting To Open the Door Manually HAVING A PROBLEM My door will not close and the light bulbs blink on my motor unit: 2.My remotes will not activate the door: My door reverses for no apparent reason: 5.My lights will not turn off when door is open: 1 FLASH FLASHES Smart Control Panel™ Messages Message To Add or Reprogram a Hand-heldRemote Control To Erase All Codes From Motor Unit Memory *3-ButtonRemotes (315 MHz) To Add, Reprogram or Change a Keyless Entry PIN Rail Assembly Parts Installation Parts Motor Unit Assembly Parts ACCESSORIES 1702LM Outside Quick Release: 373W SECURITY✚® 3-ButtonRemote Page Page LIFTMASTER FIVE-YEARLIMITED WARRANTY LIFETIME MOTOR LIMITED WARRANTY