Smart Control Panel™ Messages
The following messages are contained within the Smart Control Panel™ and may appear during the operations of the unit:
Message | Meaning: This message will appear if the Safety Reversing Sensors are out of | ||
SAFETY SENSORS | alignment, if they are blocked or if the wiring is disconnected. To clear message | ||
from Door Control do the following: | |||
CHECK ALIGNMENT, | |||
• | Check to see that area is clear between the Safety Reversing Sensors. | ||
BLOCKAGE OR | |||
MISWIRING. SEE | • | Check to see that the Safety Reversing Sensors are not misaligned. | |
OWNER’S MANUAL. |
| • Realign receiving eye sensor, clean lens and secure brackets. | |
|
| • Verify door track is firmly secured to wall and does not move. | |
| • Check to see that the Safety Reversing Sensors’ wires are connected to the motor unit. | ||
Message | • | If message has not cleared after the above checks, refer to message #2. | |
Meaning: This message will appear if the Safety Reversing Sensors are miswired. | |||
SAFETY SENSORS | To clear the message, do the following: | ||
• Inspect the safety sensor wires for a short (staple in wire), correct wiring polarity (black/ | |||
MALFUNCTION. | |||
CHECK MISWIRING. |
| white wires reversed), replace/attach as needed. | |
SEE OWNER’S | • | Disconnect all wires from back of motor unit. | |
MANUAL. | |||
• | Remove safety sensors from brackets and shorten sensor wires to | ||
| |||
|
| from back of each sensor. | |
| • | Reattach sending eye to motor unit using shortened wires. If sending eye indicator light | |
|
| glows steadily, attach the receiving eye. | |
| • | Align sensors, if the indicator lights glow replace the wires for the sensors. If the | |
Message |
| sensor indicator lights do not light, replace the safety sensors. | |
Meaning: This message will appear when the Prog <LEARN> button has been | |||
LEARN REMOTE | pressed on the Door Control. Pressing the Prog <LEARN> button again will allow | ||
the user to program an additional remote control to the opener. | |||
CONTROL. PRESS | |||
|
| ||
LEARN BUTTON TO |
|
| |
CONFIRM. |
|
| |
Message | Meaning: This message will appear when the Prog <learn> button has been | ||
LEARN MODE. | pressed a second time on the Door Control or anytime on the opener. The opener | ||
is ready to program another remote control by simply pressing the remote control | |||
PRESS REMOTE | |||
button. Once the opener has ‘LEARNED’ the remote control, the worklight will blink | |||
CONTROL BUTTON | |||
one time. | |||
TO PROGRAM | |||
|
| ||
REMOTE. |
|
| |
Message | Meaning: This message will appear when the ‘Lock’ button has been pressed and | ||
LOCK MODE. | held for more than one second. This feature will disable the opener from receiving | ||
remote control signals. To exit ‘LOCK’ mode, press and hold the button for more | |||
REMOTE CONTROL | |||
than one second. | |||
LOCKED OUT. | |||
|
| ||
PRESS LOCK |
|
| |
BUTTON TO ENABLE |
|
| |
REMOTE. |
|
| |
Message | Meaning: This message will appear when the ‘Language’ button has been pressed. | ||
ENGLISH, FRANÇAIS | Pressing the button will toggle to the next language. | ||
|
| ||
AND ESPAÑOL. |
|
| |
Message | Meaning: This message will appear when the ‘MOTION SENSING’ button is pressed. | ||
MOTION SENSING | The Motion Detector will toggle on or off with each press of the button. | ||
|
| ||
ON, MOTION |
|
| |
|
| ||
SENSING OFF. |
| 28 | |
|
| ||