INSTALLATION STEP 5
Install the Control Console
Locate control console within sight of the door at a minimum height of 5 feet (1.5 m) where small children cannot reach, and away from moving parts of the door and door hardware. The installation surface must be smooth and flat. If installing into drywall (Figure 1), drill 5/32" holes and use anchors provided. For
1.Strip 7/16" (11 mm) of insulation from one end of bell wire and connect to terminals on back of control console by color: white wire to WHT and white/red wire to the RED (Figure 3).
2.Remove cover by gently prying at slot in top of the cover with a small flat head screwdriver. Fasten with
•Drill and install bottom screw, allowing 1/8" (3 mm) to protrude above wall surface.
•Position bottom of control console on screw head and slide down to secure. Adjust screw for snug fit.
•Install top screw with care to avoid cracking plastic housing. Do not over tighten.
•Insert top tabs and snap on cover.
NOTE: The push bar may stick if the control console is not mounted on a smooth surface. If a click is not heard when pressing the push bar, loosen the two mounting screws or relocate the control console to a smoother surface.
3.(Standard installation only) Run bell wire up wall and along ceiling to motor unit. Use insulated staples to secure wire in several places. Do not pierce wire with a staple, creating a short or open circuit.
4.Strip 7/16" (11 mm) of insulation from end of bell wire. Connect bell wire to the
5.Use tacks or staples to permanently attach entrapment warning label to wall near control console, and manual release/safety reverse test label in a prominent location on inside of garage door.
NOTE: DO NOT connect the power and operate the opener at this time. The door will travel to the full open position but will not return to the close position until the sensor beams are connected and properly aligned. See Protector System Instructions beginning on page 14.
WARNING
To prevent possible SERIOUS INJURY or DEATH from electrocution:
•Be sure power is not connected BEFORE installing control console.
•Connect ONLY to 24 VOLT low voltage wires.
To prevent possible SERIOUS INJURY or DEATH from a closing garage door:
•Install control console within sight of garage door, out of reach of children at a minimum height of 5 feet (1.5 m), and away from all moving parts of door.
•NEVER permit children to operate or play with control console push buttons or remote controls.
•Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.
•ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of closing garage door.
|
| HARDWARE SHOWN ACTUAL SIZE |
| |||
| Screw |
| Insulated |
| ||
| (standard installation) |
| Staples |
| ||
Screw |
|
|
| |||
|
| Drywall Anchors |
| |||
STANDARD WALL MOUNT |
| |||||
To Replace |
|
|
|
|
|
|
Insert Top |
|
|
|
| Bell Wire |
|
Tabs First |
|
| To Replace |
|
| |
|
|
|
|
| ||
|
|
| Insert Top |
|
|
|
|
|
| Tabs First |
|
|
|
|
|
| ON |
|
|
|
|
|
| OFF |
|
|
|
| LOCK |
| Detector |
|
|
|
|
| L |
|
|
| |
Push Bar Cover | IGHT | Switch |
|
|
| |
|
| Detector | ON | |||
|
|
|
|
| ||
Figure 1 |
|
| Push Bar | LOCK | Switch | OFF |
|
|
| ||||
|
|
| LIGHT |
| ||
|
|
| Cover |
|
|
|
|
|
| Figure 2 |
|
|
|
Top |
|
|
|
|
|
|
Mounting |
|
| Bell Wire |
|
|
|
Hole |
| 2 | E |
|
|
|
|
| WHIT |
|
|
|
|
Control |
|
|
|
|
|
|
Console |
| 1 |
|
|
|
|
Terminal |
|
|
|
|
| |
| RED |
|
|
|
|
Screws
Bottom
Mounting
Hole
(BACK VIEW)
Figure 3
7/16" (11 mm)
Strip wire 7/16" (11 mm)
To release wire, push in tab with screwdriver tip
WHT/RED
Control Console
Connections WHT
Figure 4
10