OPERATION OF YOUR OPENER
Your opener can be activated by any of the following devices:
•The Lighted Door Control Button. Hold the button down until door starts to move.
•The Outside Keylock or Keyless Entry System (if you have installed either of these accessories).
•The Remote Control Transmitter. Hold the push button down until the door starts to move.
Opening the Door Manually: Door should be fully closed if possible. Weak or broken springs could allow an open door to fall rapidly. Property damage or serious personal injury could result.
The door can be opened manually by pulling the release handle down. To reconnect the door, pull the release handle down and toward the opener.
Do not use the manual release handle to pull the door opener or closed. When the Opener is Activated by Remote Control or Lighted Door Control Button:
1.If open, the door will close. If closed, the door will open.
2.If closing, the door will stop.
3.If opening, the door will stop (allowing space for entry and exit of pets and for fresh air).
4.If the door has been stopped in a partially open or closed position, it will reverse direction.
5.If an obstruction is encountered while closing, the door will reverse.
6.If an obstruction is encountered while opening, the door will reverse and stop.
7.The optional Protector System™ uses an invisible beam which, when broken by an obstruction, causes a closing door to open and prevents an open door from closing. It is STRONGLY RECOMMENDED for homeowners with
young children.
Allow a 15 minute cooling period after 5 continuous operations of the opener. The opener light will turn on: 1. when opener is initially plugged in; 2. when the power is briefly interrupted; 3. when the opener is activated.
The light turns off automatically after 2-1/2 minutes. Bulb size is 230V/40W maximum.
GARAGE DOOR OPENER WARRANTY
Chamberlain GmbH warrants to the first retail purchaser of this product that the product shall be free from any defect in materials and/or workmanship for a period of 24 full months (2 years) from the date of purchase. The motor is warrantied to be free from defects in materials and/or workmanship for a period of: ML1000A, 60 full months (5 years); ML800A, 48 full months (4 years); ML600A, 36 full months (3 years) from the date of purchase. Upon receipt of the product, the first retail purchaser is under obligation to check the product for any visible defects.
Conditions: The warranty is strictly limited to the reparation or replacement of the parts of this product which are found to be defective and does not cover the costs or risks of transportation of the defective parts or product.
This warranty does not cover non-defect damage caused by unreasonable use (including use not in complete accordance with Chamberlain’s instructions for installation, operation and care; failure to provide necessary maintenance and adjustment; or any adaptations of or alterations to the products), labor charges for dismantling or reinstalling of a repaired or replaced unit or replacement batteries.
A product under warranty which is determined to be defective in materials and/or workmanship will be repaired or replaced (at Chamberlain's option) at no cost to the owner for the repair and/or replacement parts and/or product. Defective parts will be repaired or replaced with new or factory rebuilt parts at Chamberlain's option.
If, during the warranty period, the product appears as though it may be defective, contact your original place of purchase.
This warranty does not affect the purchaser’s statutory rights under applicable national legislation in force nor the purchaser’s rights against the retailer arising from their sales/purchase contract. In the absence of applicable national or EU legislation, this warranty will be the purchaser’s sole and exclusive remedy, and neither Chamberlain nor its affiliates or distributors shall be liable for any incidental or consequential damages for any express or implied warranty relating to this product.
No representative or person is authorized to assume for Chamberlain any other liability in connection with the sale of this product.
SPECIFICATIONS
Input Voltage | 230-240 VAC, 50Hz |
Max. Pull Force | 600N (LM600A), 800N (LM800A), |
| 1000N (LM1000A) |
Power | 6Nm (LM600A), 8Nm (LM800A), |
| 10Nm (LM1000A) |
Watts | 130W (LM600A), 165W |
| (LM800A), 190W (LM1000A) |
Standby Power | 5.0W (LM600A and LM800A), |
| 5.5W (LM1000A) |
| Motor |
Type | DC gearmotor permanent |
| lubrication |
| Drive Mechanism |
Drive | Chain/belt with two-piece trolley |
| on steel rail. |
Length of Travel | Adjustable to 2,3m (7-1/2 feet) |
Travel Rate | 5"-7" (127-178mm) per second |
Lamp | On when door starts, off 2-1/2 |
| minutes after stop. |
Door Linkage | Adjustable door arm. Pull cord |
| trolley release. |
| Safety |
Personal | Push button and automatic |
| reversal in down direction. Push |
| button and automatic stop in up |
| direction. |
Electronic | Automatic force adjustment |
Electrical | Transformer overload protector |
| and low voltage push button |
| wiring. |
Limit Device | Optical RPM/Passpoint detector. |
Limit Adjustment | Electronic, Semi and Fully |
| Automatic. |
Start Circuit | Low voltage push button circuit. |
| Dimensions |
Length (Overall) | 3,2m (122-1/2") |
Headroom Required | 30mm |
Hanging Weight | 32 lb (14,5 kg) |
| Receiver |
Memory Registers | 16 (LM600A), 32 (LM800A) & |
| 64 (LM1000A) |
Operating Frequency | 433.92MHz |
SPECIAL NOTE: Chamberlain strongly recommends that the protector system be installed on all garage door openers.
D e c l a r a t i o n o f C o n f o r m i t y
The undersigned, hereby declare that the equipment specified, and all accessories, conforms to the Directives and Standards stated. Model: . . . . . . . . . . . . . . . . . . . . . .LM600A, LM800A, LM1000A
✓89/336/EEC
✓73/23/EEC
✓1999/5/EC
EN55014-1 (2000), EN55014-2 (1997), EN61000-3-2 (2000), EN61000-3-3 (1995), EN 301 489-3 (V1.3.1), EN 300 220-3 (V1.1.1), EN60335-1 (1994), and EN60335-2-95 (2000)
D e c l a r a t i o n o f I n c o r p o r a t i o n
A power door operator, in combination with a Garage Door must be installed and maintained according to all the Manufacturer’s instructions, to meet the provisions of Machinery Directive,
89/392/EEC.
B. P. Kelkhoff
Manager, Regulatory Affairs
Chamberlain GmbH
D-66793 Saarwellingen
May, 2004
