Multi-Function Door Control (Optional)
INSTALLATION

Locate door control within sight of the door at a minimum height of 5 feet where small children cannot reach, and away from moving parts of the door and door hardware. If installing into drywall, drill 5/32" holes and use anchors provided. For pre-wired installations (as in new home construction), it may be mounted to a single gang box. NOTE: After installation, a green indicator light behind the cover will indicate proper connection. If not lit, the Lock and Light features will not function (reverse wires to correct).

1.Strip 1/4" of insulation from one end of bell wire and connect to the two screw terminals on back of door control by color: white wire to 2 and white/red

wire to 1.

2.Remove white cover by gently prying on a side corner near the top of the cover with a small flat head screwdriver. Fasten with 6ABx1-1/4 "self-tapping screws (standard installation) or 6-32x1" machine screws (into gang box) as follows:

WARNING

To prevent possible SERIOUS INJURY OR DEATH from electrocution:

•Be sure power is not connected BEFORE installing door control.

•Connect ONLY to 24 VOLT low voltage wires.

To prevent possible SERIOUS INJURY or DEATH from a closing garage door:

•Install door control within sight of garage door, out of reach of children at a minimum height of 5 feet, and away from all moving parts of door.

•NEVER permit children to operate or play with door control push buttons or remote control transmitters.

•Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.

•ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of closing garage door.

• Drill and install bottom screw, allowing 1/8" to

OPERATION OF THE

protrude above wall surface.

MULTI-FUNCTION DOOR CONTROL

•Position bottom of door control on screw head and slide down to secure. Adjust screw for snug fit.

•Install top screw with care to avoid cracking plastic housing. Do not overtighten.

•Insert bottom tabs and snap on cover. (To remove cover after mounting, gently pry at top with paper clip or small flat head screwdriver.)

3.(Standard installation only) Run bell wire up wall and across ceiling to motor unit. Use insulated staples to secure wire in several places. Do not pierce wire with a staple, creating a short or open circuit.

4.Connect bell wire to the opener terminal screws: white to 2 and white/red to 1.

5.Use tacks or staples to permanently attach entrapment warning label to wall near door control, and manual release/safety reverse test label in a prominent location on inside of garage door.

NOTE: DO NOT connect the power and operate the opener at this time. The trolley will travel to the full open position but will not return to the close position until the sensor beam is connected and properly aligned. See Safety Reversing Sensor Instructions beginning on

Press the push bar to open or

close the door. Press again to

Lighted

Push Button

reverse the door during the

 

closing cycle or to stop the

Lock

door while it's opening.

Button

Light

LIGHT

LOCK

 

Light feature

Button

Press the Light button to turn the opener light on or off. It will not control the opener lights when the door is in motion. If you turn it on and then activate the opener, the light will remain on for 4-1/2 minutes. Press again to turn it off sooner. The 4-1/2 minute interval can be changed to 1-1/2, 2-1/2, or 3-1/2 minutes as follows: Press and hold the Lock button until the light blinks (about 10 seconds). A single blink indicates that the timer is reset to 1-1/2 minutes. Repeat the procedure and the light will blink twice, resetting the timer to 2-1/2 minutes. Repeat again for a 3-1/2 minute interval, etc., up to a maximum of four blinks and 4-1/2 minutes.

Lock feature

Designed to prevent operation of the door from hand-held remote controls. However, the door will open and close from the Door Control, the Outside Keylock and the Keyless Entry Accessories.

page 15.

Multi-Function

Door Control Panel

Terminal Screws

Door Control

Push Bar

RED WHT

1

2

2-Conductor Bell Wire

Lock

LOCK

LIGHT

Button

 

Opener Terminal Screws

123

9

1

9

1

7

3

7

3

 

5

 

5

KGKG

To activate, press and hold the Lock button for 2 seconds. The push bar light will flash as long as the Lock feature is on.

To turn off, press and hold the Lock button again for

2 seconds.The push bar light will stop flashing. The Lock feature will also turn off whenever the “learn” button on the motor unit panel is activated.

Light Button

Opener Panel

 

Antenna

 

28