Chamberlain HD200DM NOTE:, Wood Doors:, Metal Doors:, ONE-PIECEDOORS

ONE-PIECE DOORS

Please read and comply with the warnings and reinforcement instructions on the previous page. They apply to one-piece doors also.

•Center the door bracket on the top of the door, in line with the header bracket as shown. Mark either the left and right, or the top and bottom holes.

•Metal Doors: Drill 3/16" pilot holes and fasten the bracket with the 1/4"-14x5/8" self-threading screws provided.

•Wood Doors: Drill 5/16" holes and use 5/16"x2" carriage bolts, lock washers and nuts (not provided) or 5/16"x1-1/2" lag screws (not provided) depending on your installation needs.

NOTE: The door bracket may be installed on the top edge of the door if required for your installation. (Refer to the dotted line optional placement drawing.)

HARDWARE SHOWN

ACTUAL SIZE

Self-Threading Screw 1/4"-14x5/8"

Header Wall

2x4 Support

Header

Bracket

Door

Bracket

Optional

Placement

of Door

Bracket

Vertical

Centerline of

Garage Door

			Self-Threading
			Screw
		Door	1/4"-14x5/8"
	Finished Ceiling	Door	Top of Door
		Bracket	Top of Door
		Bracket	(Inside
			(Inside
			Garage)
			Top Edge
			of Door
			Optional
			Placement
			METAL DOOR
	HORIZONTAL AND VERTICAL
	REINFORCEMENT IS NEEDED	Nut	Lock
	FOR LIGHTWEIGHT GARAGE	5/16"-18	Lock
	FOR LIGHTWEIGHT GARAGE	5/16"-18	Washer
	DOORS (FIBERGLASS,		Washer
	DOORS (FIBERGLASS,		5/16"
	ALUMINUM, STEEL, DOORS		5/16"
	ALUMINUM, STEEL, DOORS
	WITH GLASS PANEL, ETC.).	Door	Top of Door
	(NOT PROVIDED)	Door	Top of Door
	(NOT PROVIDED)	Bracket	(Inside
		Bracket	(Inside
			Garage)
			Top Edge
			of Door
			Optional
			Placement
			Carriage Bolt
			5/16"x2"
			(Not Provided)
	For a door with no exposed framing,		WOOD DOOR
	or for the optional installation, use
	lag screws 5/16"x1-1/2" (Not Provided)
	to fasten door bracket.

24

Contents

For Residential Use Only Introduction Assembly Installation Safety Symbol and Signal Word Review Adjustment Preparing your garage door Tools needed Planning Planning (Continued) Carton Inventory Hardware Inventory Assemble the Rail & Install the Trolley Fasten the Rail to the Motor Unit Install the Idler Pulley Install the Chain/Cable Tighten the Chain Determine the Header Bracket Location Install the Header Bracket Attach the Rail to the Header Bracket Position the Opener Hang the Opener Install the Door Control Install the Light Attach the Emergency Release Rope and Handle Electrical Requirements Install The Protector System® INSTALLING THE BRACKETS Garage door track installation (preferred): Wall installation (Figure 2 & 3): Floor installation (Figure 4): MOUNTING AND WIRING THE SAFETY REVERSING SENSORS TROUBLESHOOTING THE SAFETY REVERSING SENSORS ALIGNING THE SAFETY REVERSING SENSORS Fasten the Door Bracket ONE-PIECEDOORS Metal Doors: Connect Door Arm to Trolley ALL ONE-PIECEDOORS 1.Assemble the door arm, Figure 4: 2.Adjustment procedures, Figure 5: •Open door adjustment: decrease UP travel limit •Closed door adjustment: decrease DOWN travel limit Adjust the UP and DOWN Travel Limits Adjust the Force Test the Safety Reversal System Test The Protector System® Using Your Garage Door Opener Using the Wall-MountedDoor Control To Open the Door Manually CARE OF YOUR OPENER LIMIT AND FORCE ADJUSTMENTS: THE REMOTE CONTROL BATTERY Repeat the safety reverse test (Adjustment Step 3, page 29) after any adjustment of limits or force HAVING A PROBLEM 1. My door will not close and the light bulbs blink on my motor unit: 2. My remotes will not activate the door: 3. My door reverses for no apparent reason: Repeat Diagnostic Chart Symptom: LED is not lit on door control Symptom: Motor unit doesn’t operate To Add or Reprogram a Hand-heldRemote Control To Erase All Codes From Motor Unit Memory *3-ButtonRemotes (315 MHZ) To Add, Reprogram or Change a Keyless Entry PIN Rail Assembly Parts Installation Parts Motor Unit Assembly Parts ACCESSORIES 953D 3-ButtonSECURITY✚® Remote Control : 956D CHAMBERLAIN ONE-YEARLIMITED WARRANTY SIX-YEARMOTOR LIMITED WARRANTY