Manuals / Brands / Household Appliance / Home Security System / Chamberlain / Household Appliance / Home Security System

Chamberlain HD200DM Rail Assembly Parts, Installation Parts, NO, NO, NO, NO, KEY, KEY, PART, PART, NOT SHOWN, NOT SHOWN, DESCRIPTION, DESCRIPTION, REPAIR PARTS

1 40

Download 40 pages, 1.88 Mb

REPAIR PARTS

Rail Assembly Parts

2

1

3

4

5

		KEY	PART
		NO.	NO.	DESCRIPTION
		1	4A1008	Master link kit
		2	41C5141-1	Complete trolley assembly
		3	41A5665-2	Complete rail
		4	144C56	Idler pulley
	6	5	41A5807	Chain and cable
	6	6	12D598-1	“U” bracket
		6	12D598-1	“U” bracket
				NOT SHOWN
			183A163	Wear pads

Installation Parts

1

3

6

5

8

12

13

2	4	KEY	PART
		NO.	NO.	DESCRIPTION
		1	41A4166	Lighted door control button
7		2	950D	Single-Button remote control
7		3	10A20	3V2032 Lithium battery
		3	10A20	3V2032 Lithium battery
		4	29B137	Remote control visor clip
		5	41A2828	Emergency release rope and handle
9				assembly
9		6	41B4494-1	2-Conductor bell wire, white and
		6	41B4494-1	2-Conductor bell wire, white and
				white/red
	10	7	41A5047	Door bracket w clevis pin & fastener
	10	8	41A5047-2	Header bracket w/clevis pin & fastener
		8	41A5047-2	Header bracket w/clevis pin & fastener
		9	178B35	Curved door arm section
11		10	178B34	Straight door arm section
		11	12B776	Hanging bracket
		12	41A5034	Safety sensor kit (receiving and
				sending eyes) with 3' (0.9 m)
				2-conductor bell wire
		13	41A5266-1	Safety sensor brackets (2)
				NOT SHOWN
			41A5258-11	Installation hardware bag
				(includes hardware listed on page 7)
			114A3591	Owner's manual
			114A3591SP Owner's manual - Spanish

37

Contents

For Residential Use Only Introduction Assembly Installation Safety Symbol and Signal Word Review Adjustment Preparing your garage door Tools needed Planning Planning (Continued) Carton Inventory Hardware Inventory Assemble the Rail & Install the Trolley Fasten the Rail to the Motor Unit Install the Idler Pulley Install the Chain/Cable Tighten the Chain Determine the Header Bracket Location Install the Header Bracket Attach the Rail to the Header Bracket Position the Opener Hang the Opener Install the Door Control Install the Light Attach the Emergency Release Rope and Handle Electrical Requirements Install The Protector System® INSTALLING THE BRACKETS Garage door track installation (preferred): Wall installation (Figure 2 & 3): Floor installation (Figure 4): MOUNTING AND WIRING THE SAFETY REVERSING SENSORS TROUBLESHOOTING THE SAFETY REVERSING SENSORS ALIGNING THE SAFETY REVERSING SENSORS Fasten the Door Bracket ONE-PIECEDOORS Metal Doors: Connect Door Arm to Trolley ALL ONE-PIECEDOORS 1.Assemble the door arm, Figure 4: 2.Adjustment procedures, Figure 5: •Open door adjustment: decrease UP travel limit •Closed door adjustment: decrease DOWN travel limit Adjust the UP and DOWN Travel Limits Adjust the Force Test the Safety Reversal System Test The Protector System® Using Your Garage Door Opener Using the Wall-MountedDoor Control To Open the Door Manually CARE OF YOUR OPENER LIMIT AND FORCE ADJUSTMENTS: THE REMOTE CONTROL BATTERY Repeat the safety reverse test (Adjustment Step 3, page 29) after any adjustment of limits or force HAVING A PROBLEM 1. My door will not close and the light bulbs blink on my motor unit: 2. My remotes will not activate the door: 3. My door reverses for no apparent reason: Repeat Diagnostic Chart Symptom: LED is not lit on door control Symptom: Motor unit doesn’t operate To Add or Reprogram a Hand-heldRemote Control To Erase All Codes From Motor Unit Memory *3-ButtonRemotes (315 MHZ) To Add, Reprogram or Change a Keyless Entry PIN Rail Assembly Parts Installation Parts Motor Unit Assembly Parts ACCESSORIES 953D 3-ButtonSECURITY✚® Remote Control : 956D CHAMBERLAIN ONE-YEARLIMITED WARRANTY SIX-YEARMOTOR LIMITED WARRANTY