Electrical Continued...

OPEN INPUT: Any device that is used to open the gate from a closed position is an open input device. The device used must provide normally open contacts. These normally open contacts are connected to terminals 5 and 6. These open input terminals will cause the gate operator to open and/or close if the timer switch is in the OFF position. If the timer switch is in the ON position, these open input terminals will cause the gate operator to open and will hold the gate open until the input is released and the auto close time has elapsed.

CLOSE INPUT: Any device that is used to close the gate is a close input device. The device used must provide normally open contacts. These normally open contacts are connected to terminals 9 and 10.

These close input terminals will cause the gate

RED BLK

operator to close the gate any time the gate is in a

 

non-closed position and can be used to override the

 

timer and close the gate prematurely.

 

PUSH BUTTONS,

 

KEY SWITCHES, ETC.

SAFETY ) N.O.

OPEN ) N.O.

PULSE OPEN) N.O.

N.C.STOP ) N.C.

CLOSE ) N.O.

N.O.STOP ) N.O.

REMOVE JUMPER

IF USING N.C. STOP

SAFETY NOTES: Controls must be far enough from the gate so that the user is prevented from coming in contact with the gate while operating the controls. Controls intended to be used to reset an operator after 2 sequential activations of the entrapment protection device or devices must be located in the line of sight of the gate. Outdoor or easily accessible controls shall have a security feature to prevent unauthorized use.

1

412 HM

2

RADIO RECEIVER

 

3

 

4

 

GRY

GRY

 

24

25

26

27

 

OPERATION

L R

 

 

 

 

 

 

 

LEFT/RIGHT SIDE

 

 

 

 

 

 

 

 

 

 

 

 

 

SWITCH

 

 

 

 

 

 

 

 

 

 

TIMER

 

 

 

EDGE

ALARM

COM

RADIO

AUTO

 

ADJUST

 

 

 

 

 

 

 

 

 

 

MORETIME

3

COM

SWITCH2

 

LIMITSWITCHES

 

CLOSE

 

 

 

 

 

 

ADJUST

 

1

 

SWITCH1

 

 

 

TIMER

 

TIMERSWITCH

 

 

RED

 

 

 

 

 

 

OFFON

2

 

COM

 

 

 

 

 

 

 

 

GRN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

OPEN

 

 

 

 

ORG

 

 

 

 

 

 

INCREASE

4

 

 

 

 

 

SENSITIVITY

!

 

 

 

 

 

 

 

 

 

ADJUSTMENTS

CLOSE

 

 

 

 

SAFETY

 

 

 

 

 

5

 

 

 

 

 

 

 

 

ADJUST

 

 

 

OPEN

 

 

 

 

 

INCREASE

 

 

 

ACCESSORYINPUTTERMINALS

 

 

 

 

 

COMCOM

JUMPER

ACCESSORYPOWER TDC/.1AMPOL12V

 

 

 

BLKGRNORGVLTBLU

-

 

6

 

 

 

 

 

15

 

 

 

 

 

MOTORPOWER

 

RESISTOR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PULSE

 

 

 

 

 

 

 

 

7

 

 

OPEN

 

 

 

RELAY

 

 

 

 

16

 

 

 

 

 

 

 

 

 

 

8 -

 

 

N.C.

 

 

 

NOTUSED

 

 

17

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9

 

 

STOP

 

 

 

RELAYPOWER

 

 

+ 18

 

 

CLOSE

 

 

 

 

10

 

 

 

 

 

 

 

 

 

19

 

 

N.O.

 

 

 

RELAYCOIL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11

 

 

STOP

 

 

 

START/STOP

 

 

 

 

20

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

RESITOR

 

 

 

 

12 +

 

 

 

 

 

NOTUSED

 

 

21

 

 

 

 

 

 

 

 

 

 

13 +

AC

CIRCUIT

 

 

RELAYCOIL

 

 

YLW

 

22

14 -

 

18V

BOARD

 

 

RESITOR

 

 

BLU

 

23

 

 

 

POWER

 

 

START/STOP

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

104680F

N.C. STOP INPUT: Any device that is used to stop the gate operator while it is running in the open or closed direction is a stop input device. These stop input devices must provide normally closed contacts. To connect these normally closed contacts, remove the stop jumper from terminals 8 and 9 and then connect the contacts to these same terminals 8 and 9.

N.O. STOP INPUT: This input functions identical to N.C. Stop with the exception that it requires normally open contacts. These contacts are connected to terminals 9 and 11.

SAFETY INPUT: Any device that is used to open and/or hold open the gate while the gate is in a non-closed

position is a safety input device. The safety input device must provide normally open contacts. These contacts are connected to terminals 4 and 6. This function is especially useful when the auto close timer is being used in preventing the gate from accidentally closing on a vehicle.

PULSE OPEN INPUT: This input functions similarly to the standard open input with the exception that it will not hold the gate open if the input remains present. This feature will add additional security to the gate operator system in the event that there is a device that is stuck on. Pulse open is found at terminals 6 and 7.

15