Char-Broil 463722312 Sideburner Ignitor Lighting, Sideburner Match Lighting, Burner Flame Check

WARNING

Turn controls and gas source or tank OFF when not in use.

CAUTION

If ignition does NOT occur in 5 seconds, turn the burner controls OFF, wait 5 minutes and repeat the lighting procedure. If the burner does not ignite with the valve open, gas will continue to flow out of the burner and could accidently ignite with risk of injury.

Match-Lighting

sDo not lean over grill while lighting.

1.Turn OFF gas burner control valves.

2.Turn ON gas at LP cylinder.

3.Open lid during lighting.

4.Place match into match holder (hanging from side of cart). Strike the match.

5.Place lit match through the match light hole and near the burner. Push in and turn left knob to the HI position. Be sure the burner lights and stays lit.

6.Light adjacent burners in sequence by pushing knobs in and turning to the HI position.

NOTE: Your grill may NOT be equipped with a Sideburner!

Sideburner Ignitor Lighting

1.Turn OFF gas burner control valves.

2.Turn ON gas at LP cylinder.

3.To ignite SIDEBURNER, open sideburner cover.

4.Turn sideburner knob to the HI position. Push IGNITOR button rapidly.

5.If sideburner does not light in 5 seconds, turn knob to OFF, wait 5 minutes, then repeat lighting procedure.

Sideburner Match Lighting

1.Turn ON gas at LP cylinder.

2.Hold lit match to any port on

the burner. Push in and turn sideburner knob to the

HI position.

Be sure the burner lights and stays lit.

Burner Flame Check

•Remove cooking grates and flame tamers. Light burners, rotate knobs from HI to LOW. You should see a smaller flame in LOW position than seen on HI. Perform burner flame check on sideburner, also. Always check flame prior to each use. If only low flame is seen refer to "Sudden drop or low flame" in the Troubleshooting Section.

HI

LOW

Turning Grill Off

•Turn all knobs to the OFFposition. Turn LP cylinder OFF by turning hand-wheel clockwise to a full stop.

Ignitor Check

•Turn gas off at LP cylinder. Press and hold electronic ignitor button. "Click" should be heard and spark seen each time between each collector box or burner and electrode. See "Troubleshooting" if no click or spark.

Valve Check

•Important: Make sure gas is off at LP cylinder before checking valves. Knobs lock in OFF position. To check valves, first push in knobs and release, knobs should spring back. If knobs do not spring back, replace valve assembly before using grill. Turn knobs to LOW position then turn back to OFF position. Valves should turn smoothly.

Hose Check

•Before each use, check to see if hoses are cut or worn or linked. Replace damaged hoses before using grill. Use only valve/hose/regulator specified by manufacturer.

General Grill Cleaning

•Do not mistake brown or black accumulation of grease and smoke for paint. Interiors of gas grills are not painted at the factory (and should never be painted). Apply a strong solution of detergent and water or use a grill cleaner with scrub brush on insides of grill lid and bottom. Rinse and allow to completely air dry. Do not apply a caustic grill/oven cleaner to painted surfaces.

•Plastic parts: Wash with warm soapy water and wipe dry.

useDo not citrisol, abrasive cleaners, degreasers or a concentrated grill cleaner on plastic parts. Damage to and failure of parts can result.

•Porcelain surfaces: Because of glass-like composition, most residue can be wiped away with baking soda/water solution or specially formulated cleaner. Use nonabrasive scouring powder for stubborn stains.

•Painted surfaces: Wash with mild detergent or nonabrasive cleaner and warm soapy water. Wipe dry with a soft nonabrasive cloth.

•Stainless steel surfaces: To maintain your grill’s high quality appearance, wash with mild detergent and warm soapy water and wipe dry with a soft cloth after each use. Baked-on grease deposits may require the use of an abrasive plastic cleaning pad. Use only in direction of brushed finish to avoid damage. Do not use abrasive pad on areas with graphics.

•Cooking surfaces: If a bristle brush is used to clean any of the grill cooking surfaces, ensure no loose bristles remain on cooking surfaces prior to grilling. It is not recommended to clean cooking surfaces while grill is hot.

12