Char-Broil 7101366 manual Ignitor Lighting, View is from side of appliance Burner Flame Check

Ignitor Lighting

•Do not lean over appliance while lighting.

1. Turn ON LP gas cylinder.

2.Press and turn the control knob to HIGH.

3.Turn ROTARY IGNITOR knob rapidly.

4.If ignition does not occur in 5 seconds, turn the burner control knob OFF, wait 5 minutes, and repeat lighting procedure.

If ignition still does not occur, follow match-lighting instructions.

WARNING

Turn control knob and LP cylinder OFF when not in use.

CAUTION

If ignition does NOT occur in 5 seconds, turn the control knob OFF, wait 5 minutes and repeat the lighting procedure. If the burner does not ignite with the valve open, gas will continue to flow out of the burner and could accidently ignite with risk of injury.

Match-Lighting

sDo not lean over appliance while lighting. 1. Turn ON LP cylinder.

2.Swing match hole plate to expose match lighting hole. Place lit match into match lighting hole of appliance as pictured below. Make sure lit match is placed inside hole and near burner.

3.Push in and turn control knob to HIGH. Be sure burner lights and stays lit.

4.Once lit, swing match hole plate back to cover up match lighting hole. Caution: Plate maybe hot.

Control

Knob

Match

Match Lighting

HoleHole

Plate

Swing Plate to expose Matchlighting Hole

Match

View is from side of appliance

Burner Flame Check

•Light burner, rotate knob from HIGH to LOW. Looking through viewing hole on top of appliance, you should see the flame height decrease when turning knob from HIGH to LOW. Always check flame prior to each use. If only low flame is seen refer to "Sudden drop or low flame" in the Troubleshooting Section.

Turning Appliance Off

•Turn control knob to OFF position. Turn LP cylinder off by turning hand-wheel clockwise to a full stop.

Ignitor Check

•Turn gas off at LP cylinder. Turn ignitor knob. "Click" should be heard each time at electrode. See "Troubleshooting" if no click or spark.

Valve Check

•Important: Make sure gas is off at LP cylinder before checking valve. Knob locks in OFF position. To check valve, first push in knob and release, knob should spring back. If knob does not spring back, replace valve assembly before using Oil- less Fryer. Turn knob to HIGH position then turn back to OFF position. Valve should turn smoothly.

Hose Check

•Before each use, check to see if hose is cut, worn or kinked. Replace damaged hose before using applaince. Use only valve/hose/regulator specified by manufacturer.

NormalKinked

HoseHose

General Appliance Cleaning

•Meat Thermometer: Do not immerse or soak in water. Wash with warm soapy water and wipe dry.

•Do not mistake brown or black accumulation of grease and smoke for paint. Interiors are not painted at the factory (and should never be painted). Apply a strong solution of detergent and water or use a grill cleaner with scrub brush on insides of appliance lid and bottom. Rinse and allow to completely air dry.

Do not apply a caustic grill/oven cleaner to painted surfaces.

•Plastic parts: Wash with warm soapy water and wipe dry. Do not use citrisol, abrasive cleaners, degreasers or a concentrated grill cleaner on plastic parts. Damage to and failure of parts can result.

•Painted surfaces: Wash with mild detergent or non-abrasive cleaner and warm soapy water. Wipe dry with a soft non- abrasive cloth.

•Stainless steel surfaces: To maintain the high quality appearance, wash with mild detergent and warm soapy water and wipe dry with a soft cloth after each use. Baked-on grease deposits may require the use of an abrasive plastic cleaning pad. Use only in direction of brushed finish to avoid damage. Do not use abrasive pad on areas with graphics.

8 • 07101366