
General Troubleshooting
Symptom
Solution(s)
Applies to
| Foggers |
| Dimmers |
Lights | & Snow | Controllers | & Chaser |
|
|
|
|
| Auto shut off |
| Check fan thermal switch reset | |
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| Beam is very dim or |
| Clean optical system or replace lamp | |
|
|
|
| not bright |
| Check 220/110v switch for proper setting |
|
|
|
|
|
|
|
|
|
|
|
|
| Breaker/Fuse keeps |
| Check total load placed on device |
|
|
| |
| blowing |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Chase is too slow |
| Check users manual for speed adjustment | |
| | |
|
|
|
|
|
|
|
|
| Device has no power |
| Check for power on Mains. | |
| | |
|
|
| Check device’s fuse. (internal and/or external) |
|
|
|
|
| Fixture is not |
| Check DMX Dip switch settings for correct addressing | |
|
|
|
| responding |
| Check DMX cables |
|
|
|
|
|
|
| Check polarity switch settings |
|
|
|
|
|
|
|
|
|
|
|
|
| Fixture is on but |
| Make sure you have the correct audio mode on the |
|
|
|
|
| there is no |
| control switches. If audio provided via ¼” jack, make | |
| | |
| movement to the |
| sure a live audio signal exists |
|
|
|
|
| audio |
| Adjust sound sensitivity knob |
|
|
|
|
|
|
|
|
|
|
|
|
| Lamps cuts off |
| Possible bad lamp or fixture is overheating. | |
|
|
|
| sporadically |
| Lamp may be at end of its life. |
|
|
|
|
|
|
|
|
|
|
|
|
| Light will not come |
| Some discharge lamps require a cooling off period | |
|
|
|
| on after power failure |
| before the electronics in the fixture can kick start it |
|
|
| |
|
|
|
|
|
| ||
|
|
| again, wait 5 to 10 minutes before powering up |
|
|
|
|
|
|
|
|
|
|
|
|
| Loss of signal |
| Use only DMX cables |
|
|
|
|
|
|
| Install terminator | | | | |
|
|
| Note: Keep DMX cables separated from power cables |
|
|
|
|
|
|
| or black lights. |
|
|
|
|
|
|
|
|
|
|
|
|
| Moves slow |
| Check 220/110v switch for proper setting | |
|
|
|
|
|
|
|
|
|
|
|
| No flash |
| |
|
|
| |
|
|
|
|
|
|
|
|
| No laser output |
| Bounce mirror motor may have shifted during shipping, | |
|
|
|
|
|
| readjust |
|
|
|
|
|
|
|
|
|
|
|
|
| No light output |
| Check slip ring & brushes for contact | |
|
|
|
|
|
| Install bulb |
|
|
| |
|
|
|
|
|
|
| |
|
|
| Call service technician |
|
|
|
|
|
|
|
|
|
|
|
|
| Relay will not work |
| Check reset switch |
|
|
| |
|
|
| Check cable connections |
|
|
|
|
|
|
|
|
|
|
|
|
| Remote does not |
| Make sure connector is firmly connected to device | | |
|
|
| work |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Stand alone mode |
| All Chauvet lighting fixtures featuring |
|
|
|
|
|
|
|
|
|
| ||
|
|
| functions do not require additional settings, simply | |
|
|
|
|
|
| power the fixture and it will automatically enter into this |
|
|
| |
|
|
| mode |
|
|
|
|
|
|
|
|
|
|
|
|
If you still have a problem after trying the above solutions, please contact CHAUVET Technical Support at the location on the next page.
LEDsplash™ 152B User Manual | 15 | 3/9/2010 3:02 PM |