Lens Assembly Installation/Replacement

The COLORado™ 6 comes with 15lens assembly pre-installed from the factory. However, there are 2 other optional lens assemblies available as accessories which will alter the beam angle. Please follow the below instructions for proper replacement/installation.

6 screws around each LED module

5 screws that hold the lens

 

assembly in place

Lens assembly

 

1.

There are 6 screws located around each module.Remove all 18 screws for the front cover.

 

2.

After removing the front cover, there are 5 screws that hold each lens assembly in place over the

 

 

LED’s. Remove these and take out the lens assembly.

 

3.

Place the new lens assembly over the Led’s, being careful to get the correct alignment.

 

4.

Replace the outer plastic cover, being careful to make a watertight seal.

Note

The center module is different from the outer 2 modules.

Note

There are multiple possible positions in which to place the lens assembly over the LEDs.

 

Failure to install it properly can lead to loss of light output and/or damage to the physical

 

LEDs. Please see the diagram located above to prevent this.

Warning!

When replacing the lens assembly, please make sure that the power is disconnected from the

 

fixture beforehand.

Please also make sure that the covers are sealed tightly when replacing them after the new lens assembly is installed, as failure to accomplish this will compromise the IP66 protection, and possibly the warranty.

Fixture Linking

 

You will need a serial data link to run light shows of one or more fixtures using a DMX controller or to

 

run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined

 

number of channels required by all the fixtures on a serial data link determines the number of fixtures

 

the data link can support.

Important

Fixtures on a serial data link must be daisy chained in one single line. To comply with the EIA-485

 

standard no more than 32 fixtures should be connected on one data link. Connecting more than 32

 

fixtures on one serial data link without the use of a DMX optically-isolated splitter may result in

 

deterioration of the digital DMX signal.

 

Maximum recommended serial data link distance: 500 m (1640 ft)

 

Maximum recommended number of fixtures on a serial data link: 32

COLORado™ 6 User Manual

11

7/1/2009 4:46 PM

Page 11
Image 11
Chauvet 6 user manual Lens Assembly Installation/Replacement, Fixture Linking

6 specifications

The Chauvet 6 is a cutting-edge lighting fixture designed to elevate the experience for events ranging from concerts and theaters to corporate presentations and parties. Aimed at both professionals and enthusiasts, the Chauvet 6 incorporates advanced technologies and innovative features that ensure stunning visuals and reliable performance.

One of the standout characteristics of the Chauvet 6 is its incredible brightness, powered by high-quality LEDs that provide vibrant colors and exceptional clarity. The fixture typically boasts multiple LED sources that can produce a wide spectrum of hues, allowing users to create dynamic lighting effects that energize any space. With its impressive lumen output, the Chauvet 6 can easily illuminate large venues or outdoor events, making it a versatile choice for various applications.

In terms of control options, the Chauvet 6 offers flexibility and ease of use. It supports DMX protocols, providing users with the ability to synchronize multiple fixtures for cohesive light shows. Additionally, many models come equipped with built-in programs that allow for stand-alone operation, eliminating the need for complex setup at smaller events. The intuitive interface and user-friendly controls enable both seasoned lighting designers and novices to craft elaborate lighting setups quickly.

Another notable feature of the Chauvet 6 is its durability and reliability. Designed with robust materials, the fixture can withstand the rigors of regular transport and usage in demanding environments. Many units feature weather-resistant casings, making them suitable for outdoor events, where they can endure changing conditions without compromising performance.

The Chauvet 6 incorporates advanced thermal management technology, which ensures that the LEDs remain at optimal operating temperatures. This not only enhances the lifespan of the fixture but also maintains color accuracy and intensity. Furthermore, the energy-efficient design minimizes power consumption, aligning with today’s eco-conscious standards.

With its mix of innovation, versatility, and performance, the Chauvet 6 stands out as a premier choice for lighting designers. Whether enhancing a stage production or adding flair to a wedding, this lighting fixture guarantees an unforgettable visual experience for audiences and participants alike. As the demand for high-quality, dynamic lighting increases, the Chauvet 6 continues to lead the way with its remarkable features and dependable technology, making it a staple in the world of event production.