Child Craft CCH00701:09/00 manual Diagram 2 Install Stabilizer Bars, Install Crib Dropsides

2				CCH00701:09/00
		STEP 2 - DIAGRAM 2: INSTALL STABILIZER BARS.
Attach each	Stabilizer Bar J	to crib ends N and O. Refer to Diagram 2 and MAIN		A
DIAGRAM 6.	You will use a	total of (8) Slotted/Phillips Machine Screws A. Place a
				Extended
Slotted/Phillips Machine Screw A into top receiving bushing, designated for Stabilizer					Keyhole
Bar J placement, located in ends O & N as shown, leave each top screw extended
- do not tighten at this time. Place the keyhole (top hole in each end of Stabilizer Bar			J
J, over top extended Screws A (which you have just installed and left extended), refer
to Diagram. Ends N and O will now be mounted together on one side of crib, repeat
this procedure for mounting the remaining Stabilizer Bar J to the other side of the crib
in the exact same manner. Place four Slotted/Phillips Machine Screws A into the lower			A		O
receiving holes in each end of both Stabilizer Bars J, into receiving bushings located in
ends N & O, tighten all eight Slotted/Phillips Machine Screws A securely at this time.
				I
				Factory
				installed

STEP 3 - DIAGRAM 3: ATTACH GATE SHOES TO DROPSIDES.

Position two Gate Shoes C to lower rail (inside) of each Crib Side P/Q as shown. Note: Gate Shoe Patent No. will be visible when Gate Shoes C are mounted. Align Gate Shoes C over predrilled lead holes on lower rail (inside) of Crib Side P/Q (dropsides) and affix with (8) Slotted/Phillips Wood Screws E, two in each Gate Shoe C. Tighten Screws E securely. Note: When disassembling crib in the future, DO NOT REMOVE THE GATE SHOES C OR

ANY OTHER HARDWARE ITEM ATTACHED WITH SLOTTED/PHILLIPS WOOD SCREWS E.

C

P o r Q

C

E

STEP 4 - DIAGRAM 4: INSTALL SPRING HANGERS & CRIB SPRING

Locate Crib Spring R, (with plastic pouch factory attached), and the four Spring Hangers B, refer to Main Diagram 6, and 4. Note: Be sure smooth side of Crib Spring R wire is placed upward as illustrated in Main Diagram 6. Also the printing on the plastic pouch (attached to crib spring) will be placed upward. Insert Spring Hangers B into each bracket attached to frame of Crib Spring R as shown, (a light blow with a hammer may be required to fully engage Spring Hangers B). Carefully install Crib Spring R by placing each of the 4 Spring Hanger B into a selected position in each of the four 4-Position Spring Hanger Brackets D, (with moulded plastic backers), mounted on ends O and N. See Main Diagram 6, and 4. Note: The lip of the moulded plastic backer will allow the Spring Hanger to be placed with no difficulty. However, when you decide on another placement of Crib Spring R you will need to place your thumbnail, or a small screwdriver, on the lip of the moulded plastic backer and hold down in order to raise Spring Hanger B from its present position. Follow this same procedure whenever you opt to change Crib Spring R to another of the four positions.

To remove Spring Hanger B press down on lip with thumbnail or screw- driver and pull Spring Hanger B upward.

R

B D

CLOSE UP

VIEW

E B

STEP 5: INSTALL CRIB DROPSIDES

Locate Crib Rods K, Crib Sides P/Q, Compression Springs F, Bumper Springs G and the four remaining Slotted/Phillips Machine Screws A. Insert a Crib Rod K downward through the holes in the following sequence: (Refer to Main Diagram 6 for proper placement.)

1.The top rail of Crib Side P or Q, (with plastic teething rail), (Note: gate shoes will be placed to inside),

2.The L- bracket on 4-Position Spring Hanger Bracket D,

3.Compression Spring F,

4.Bottom Rail of Crib Side P or Q,

5.A Bumper Spring G,

6.Hole in Angle Bracket I.

Place a Slotted/Phillips Machine Screw A into hole in top of Crib Rod K and into receiving bushing located in top corner post of Footboard O/ Headboard N. Refer to Main Diagram 6 for proper placement. DO NOT

USE A POWER SCREWDRIVER OF ANY TYPE TO TIGHTEN SCREW A. Start Screw A (two or three turns) with your fingers into its threaded bushing to insure Screw A has a square fit. Once you are sure Screw A fits squarely into its threaded bushing, tighten securely with a hand held screwdriver. Attach the other Crib Rod K to the other end of Crib Side P or Q,, using the same procedure. Be sure Slotted/Phillips Machine Screws A are tightened securely, check periodically and tighten if needed. Tip: To help Crib Rods K function more quietly we suggest you rub the crib rod with waxed paper or paraffin. You may want to repeat this procedure periodically. Attach the remaining Crib Side P or Q, by repeating Step 5.