Operations Common to Each Mode

Operations Common to Each Mode

English

Setting the clock

This unit displays the time when the car engine is running (ACC ON).

The clock is displayed in 12-hour format.

•When a navigation system is connected, the clock cannot be adjusted as clock data is sent from the navigation system.

1. Press the [ADJ] button. The previously

Selecting the sampling frequency (SAMPLING)

●About the sampling frequency

You can switch between 96 kHz and 48 kHz as the sampling frequency.

When the sampling frequency is set to 96 kHz, high band spread, depth of tones and transparency of sound are improved.

∗The factory default setting is "fs=96 kHz".

Adjusting the filter (FILTER/X- OVER)

The filter can be adjusted for each speaker. For details, see "About filter settings" (page 18).

∗The filter can be adjusted when the Audio mode is the Standard mode or the Multi mode.

1. Press the [ADJ] button.

2. Press the [ ] or [ ] button to select "SOUND".

7.

Press the [

] button.

8.

Press the [

] or [ ] button to select the

speaker adjustment item. Each press of the buttons switches the adjustment item.

Blinking

fc LPF (filter frequency of low-pass filter)*

English

adjusted item "CLOCK", for example, is

displayed on the title display, and the mode

changes to the Adjust mode.

2. Press the [ ] or [ ] button to select "CLOCK".

3.Press the [s] button. The time at adjustment (e.g. "PM 2:20") is displayed, and the mode changes to the Clock setup mode.

Blinking

*The clock is not adjusted if you press any other button while you are setting the clock.

4.

Press the [

] or [

] button to select hours

 

or minutes. Items that are blinking can be

 

adjusted.

 

 

5.

Press the [

] or [

] button to set the setting

 

for the item.

 

 

6.Press the [s] button.

You will hear a short high-pitched sound, and the clock will be set.

Note:

•You cannot set the clock when it is displayed with the power turned OFF.

•Set the clock again if you remove the battery for inspection or repairs.

1. Press the [ADJ] button.

2.

Press the [

] or [

] button to select

 

"SAMPLING".

 

3.

Press the [

] or [

] button to select

 

"fs=96kHz" or "NORMAL" (fs=48kHz).

4.Press the [ADJ] button to return to the previous mode.

Selecting the audio mode (MODE)

∗The factory default setting is "STANDARD".

●Standard mode <STANDARD>/Multi mode <MULTI>

This is used to make various sound adjustments for playback. For details, see "About the Standard mode and Multi mode" (page 18)

●Direct mode <DIRECT>

This is used to playback tones as they are without adjusting the tones of this unit. The configuration of the speaker system becomes "front (2ch) + rear (2ch) + non-fader (2ch)."

1. Press the [ADJ] button.

2. Press the [ ] or [ ] button to select

"MODE".

3. Press the [s] button.

4. Press the [ ] or [ ] button to select "FILTER" or "X-OVER".

∗Select "FILTER" when the Audio mode is the Standard mode, and "X-OVER" when the Audio mode is the Multi mode.

5. Press the [ ] or [ ] button to select " FRONT" or "HIGH".

∗Select "FRONT" when the Audio mode is the Standard mode, and " HIGH" when the Audio mode is the Multi mode.

6. Press the [ ] or [ ] button to select the speaker to adjust.

∗The mute function of a selected speaker can be turned ON/OFF by pressing the [ROTARY] knob while the speaker is selected.

Each press of the buttons switches the setting as follows:

In the Standard mode:

In the Multi mode:

FRONT

HIGH

FRONT

MID

REAR

LOW

SLP LPF (filter slope of low-pass filter)*

fc HPF (filter frequency of high-pass filter)*

SLP HPF (filter slope of high-pass filter)*

G (gain)*

PHASE (phase)*

*Sometimes this is not displayed depending on the selected speaker.

9.Press the [s] button. The setting value blinks.

10.Press the [] or [ ] button to adjust the setting.

∗For details of the adjustment ranges of each adjustment item, see "About filter settings" (page 18).

11.When you have finished the adjustment, press the [s] button to return to the screen in step 8. This sets the setting value.

12.Repeat steps 8 to 11 to adjust the adjustment items for the selected speaker.

13.When you have finished the adjustment, press the [ ] button to return to the screen in step 6.

7.Press the [ADJ] button to return to the previous mode.

3. Press the [ ] or [ ] button to select

"STANDARD", "DIRECT" or "MULTI".

4.Press the [ADJ] button to return to the previous mode.

SUB-W

SUB-W

14.Repeat steps 6 to 13 to adjust the filter of

each speaker.

 

 

15.Press the [ADJ] button to return to the previous mode.

16

DRZ9255

DRZ9255

17