ELITE WEATHERMASTER® 6 SCREENED TENT

MODEL 2000001588

Before you begin

Read all instructions before set up.

Select a level site clear of rocks, branches, and other hard or sharp objects, to install your tent.

WARNING: Keep clear of overhead power lines.

Do not set up your tent under trees because of potential lightning strikes or falling tree limbs in inclement weather.

Secure with all stakes and guylines provided to prevent property damage or personal injury.

For best results in windy conditions, position narrow end of tent into the wind.

Enlist the help of at least one other person to assist you when it is time to assemble the tent.

Pole Descriptions

Description

Qty.

Pole

Pole

Pole

Dia.

Repair Kit

Replacement Kit

Long Leg Pole, steel

 

 

 

 

(w/ red marking)

4

19mm

N/A

5010000608

Short Leg Pole, steel

4

19mm

N/A

5010000610

Curved Ridge Pole, steel

 

 

 

 

(w/ red marking)

2

19mm

N/A

5010000607

Curved Ridge Pole, steel

2

19mm

N/A

5010000609

Awning Pole, black,

 

 

 

 

fiberglass, metal tips

1

6.3mm

5010000543

5010000545

Door Pole, long, thin, black,

 

 

 

 

fiberglass, rubber tips

1

6.3mm

5010000543

5010000545

Vert. Door Pole, short, black,

 

 

 

fiberglass, rubber tips

1

6.3mm

5010000543

5010000545

Self-Rolling Window Spring Descriptions

Color Code Description

Qty.

Length

Replacement Part No.

Red

1

360mm

5010000624

Curved Ridge Poles with Red Markings in center sleeves

Fig. 6

 

 

 

 

6.Rotate all eight Leg Poles upright and insert pin on

each web loop at the side locations as shown.

7A

(Fig. 7 & 7A)

 

Pin

Fig. 7

7. Locate the plastic hooks at sides and corners of tent, then snap onto Leg Poles to attach. (Fig. 8)

Fig. 8

STITCH LINE

Green

3

610mm

5010000627

Orange

2

670mm

5010000628

CAUTION: “Springs” may have sharp edges. Handle with care to avoid injury. Keep out of reach of children.

To Set Up Tent

1.Unfold tent and spread out on a clean, level surface with the door facing the desired direction. Unzip doors. (Fig. 1)

Fig. 1

8.To stretch tent to finished size:

Push in button on Leg Pole while twisting lower Leg Pole section counterclockwise (Fig.9);

Pull up on top Leg Pole section until tent is taut;

Twist the lower Leg Pole clockwise until the button locks into the center or lowest hole;

Repeat on remaining Leg Poles.

Fig. 9

Upper

Leg Pole

Section

Button

Center Hole

Lower Hole

Lower

Leg Pole

Section

Door

2. Pull four corners of tent taut, then secure by

 

 

 

 

 

 

 

 

 

driving stakes through web loops at an angle for

 

 

 

 

 

better anchoring. (Fig. 2)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fig. 2

 

 

 

3. Assemble four, steel, shock-corded, curved

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fig. 3

Ridge Poles. Insert Ridge Poles (with red

 

 

 

 

 

 

 

 

Ridge Pole

 

 

 

marking) into center sleeves on top of tent

 

 

with Red

 

 

 

with the red trim (Fig. 3). Insert the remain-

 

 

 

Marking

 

 

 

ing curved Ridge Poles into the other two

 

 

 

 

 

 

 

 

 

sleeves on top of tent.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sleeve

 

 

 

 

 

 

 

 

 

 

with Red

 

 

 

 

 

 

 

 

 

 

 

Trim

 

4. Assemble eight, steel, shock-corded, Leg

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Poles. Push down on steel button on tapered

 

 

 

 

 

 

 

 

 

end and insert into end with four holes.

 

 

 

 

 

 

 

 

 

NOTE: Make sure steel button locks into

 

 

 

 

Button in third hole

third hole on pole as shown. (Fig.4)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Fig. 4

5. Insert curved end of Leg Poles

 

 

 

 

 

 

 

(with red marking) into the

 

 

 

 

 

 

 

 

 

 

 

ends of the Ridge Pole

 

 

 

 

 

 

 

 

 

 

 

(with red marking). Insert

 

 

Ridge Pole with

 

 

 

 

curved end of remaining

 

 

 

Red Marking

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

short Leg Poles into the

 

 

 

 

 

 

 

 

 

 

 

ends of the remaining

 

 

 

 

 

 

 

 

 

 

 

Ridge Poles. (Fig. 5 & 6)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Sleeve

 

 

 

Curved End of

 

 

 

 

Long Leg Pole

 

 

with Red

 

 

 

 

 

 

 

 

 

 

 

Trim

 

 

Fig. 5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9. Insert plastic stakes through web straps located

 

on both sides of tent, then drive in to secure.

 

(Fig. 10)

 

NOTE: It may be necessary to remove metal

 

stakes through web straps at side of tent and

 

screen room, pull tent taut, and drive in stakes

 

to secure.

Fig. 10

 

Hinged, Rigid Door

1.Assemble Vertical Door Pole (shorter black pole with plastic tips); then insert through zippered vertical pole sleeve on hinged side of door. (Fig. 11)

2.Insert end of Vertical Door Pole into bottom hinge plate, apply pressure to form a slight bow, then insert other tip of pole into top hinge. Zip up vertical pole sleeve. (Fig. 12 & 13)

3.Assemble Door Pole (longer black pole with plastic cap tips); then insert into zippered pole sleeve at top of door. (Fig. 14)

4.Insert end of Door Pole into top hinge plate, apply pressure to form a bow, then insert other tip of pole into the bottom hinge. (Fig. 15)

5.Zip up pole sleeve to enclose Door Pole. (Fig. 16)

Fig. 11

Fig. 12

Fig. 13

Vertical Pole

Sleeve

Door Hinge

 

 

Fig. 14

 

 

Fig. 15

 

 

 

Top

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Door

Pole

 

 

 

 

 

 

Hinge

 

 

 

 

 

Fig. 16

Sleeve

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(continued on other side)

Page 1
Image 1
Coleman 2000001588 manual Pole Descriptions, Self-Rolling Window Spring Descriptions, To Set Up Tent, Hinged, Rigid Door