Coleman 2000001588 Tent Lighting System, Self-rolling Windows To Attach Rainfly, Cooler Access

Sleeve Fig. 24

Color “Flag”

Color

Dot Fig. 25

Push in at top to

engage “spring(s)”

Fig. 28

Color “Flag”

Tent Lighting System

Your tent comes pre-wired with the Coleman® Tent Lighting System. See manual that came with the light and carefully read all instructions before use then save for future reference.

Self-rolling Windows (continued)

CAUTION: All “springs” must be removed from sleeves before tearing down tent to avoid damage to the tent fabric or part. To avoid injury, carefully roll up “springs”. Keep out of reach of children. Store rolled “springs in bag with stakes.

To Attach Rainfly

1.Drape Rainfly over tent. Make sure seams on Rainfly are facing down and centered over poles of the tent. (Fig. 17)

NOTE: Hook and loop fasteners, located on seams of underside of Rainfly, should be centered over Ridge Poles.

Rainfly

Sleeve

Door

Attaching Room Divider

1.Divider Panel can be installed through center of the tent by inserting the toggles through

top and bottom fabric loops as shown.

(Fig. 29 & 30)

Fig. 29

Top

Fabric

Loops

Divider
Panel	Fig. 30

					Fig. 17
2. Assemble thin, black, shock-corded
			Awning		Fig. 18
Awning Pole with metal tips; then			Pole
insert through sleeve in Rainfly above
door. (Fig. 18)
				Sleeve
3. Insert tapered metal tip on Awning
		Grommet
Pole into grommet located on web
strap clipped to center Leg Pole.
	Awning Pole
(Fig. 19)

4. Go to opposite center Leg Pole on
other side of door and gradually
apply pressure to the pole forming				Fig. 19
an arch. Insert metal tip into the
grommet.
				Fig. 20
5. Locate all hook & loop fasteners on underside
of Rainfly and wrap around Leg Poles and
Awning Pole locations. (Fig. 20)
6. Insert metal hook on
		Center
elastic straps on		Leg Pole
Rainfly into the hole		Location	End Leg
on each Leg Pole.			Pole
(Fig. 21 & 22)			Location
	Fig. 21			Fig. 22

7.Loop ends of guylines over stakes, stretch tight, then hammer into ground at an angle as shown. (Fig. 23 & 23A)

Fig. 23

Guyline

23A

Self-rolling Windows

CAUTION: “Springs” may have sharp edges. Handle with care to avoid

injury. Keep out of reach of children.

NOTE: Carefully unroll metal “springs” stored in bag with stakes. The color marking on each “spring” should match the color of the fabric “flag” sewn to the window or door sleeve opening. (Fig. 24)

1. Locate sleeve(s) in window panel, open hook & loop fastener; then insert “spring(s)” with match-

ing color marking. (Fig.24 & 25)

NOTE: When inserting into the sleeve(s), the color marking on the “spring(s)” should always face the operator.

2.Close hook & loop fastener to secure.

3. Before unzipping and opening the window, push in at top to engage “spring(s)” to activate the self-rolling feature. (Fig. 26)

4. Unzip to allow the window panel to roll down automatically; zip back to close window panel. (Fig. 27 & 28)

NOTE: Repeat steps above for inserting the color matching “spring(s)” into sleeve(s) for the rest of the windows.

Fig. 26	Door	Window Panel
	Window
	Panel
		Sleeves

Fig. 27

Electrical Cord Access Fig. 31

1.Unzip the access panel in the lower left corner of tent and bring in an electrical cord.

NOTE: Use only UL approved cords rated for outdoor usage. (Fig. 31)

Cooler Access

The smaller zippered opening at the side of tent is designed for added ventilation and easy access to your beverage cooler.

1.To use as a vent, unzip flap to expose screen.

2.To use as a cooler access, unzip other flap to

make an avenue to bring beverages into tent.
	Fig. 32
(Fig. 32)

To Store

1.All “springs” must be rolled up and placed in bag with stakes.

2.All poles and stakes must be placed in the storage bag to prevent damage to the fabric items placed in the carry case.

3.Make sure tent is clean and dry before placing in carry case.

4.Remove rainfly, spread out on floor of tent, then unzip door & vents before taking tent down for storage.

5.Neatly fold tent to width of pole storage bag, place on tent, roll tightly, and place in carry case.

5.Store in a clean, dry area.

Things You Should Know:

•Under certain conditions (cold weather, high humidity, etc.) condensa- tion will form on the inside of your tent. Condensation is caused by water vapor from your breath, perspiration, or any wet clothing inside the tent. It is NOT LEAKAGE through the tent fabric. It can be minimized by removing wet clothing from your tent and by providing good ventila- tion through the tent.

•Tree limbs, tree sap, bird droppings, or moisture steadily dripping off tree limbs can cause damage to the tent fabric and its coating resulting in leaks or loss of flame-resistant properties.

•Never store tent, even for a short period of time, without drying it thoroughly and brushing off caked dirt. Do not pack stakes or poles inside your tent. Use a separate storage bag.

•Stakes should be removed by pulling on the stake itself. NEVER PULL ON THE TENT TO REMOVE STAKES AS THIS COULD RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY.

•Tent poles should not be left telescoped together during storage.

•Do not leave your tent set-up for weeks at a time. Be aware that exposure to ultraviolet rays from the sun can seriously damage material and/or cause it to become discolored.

WARNING: Keep all flame and heat sources away from this tent fabric.

This tent meets the flammability requirements of CPAI-84. The fabric may burn if left in continuous contact with any flame source. The application of any foreign substance to the tent fabric may render the flame-resistant properties ineffective.

The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219

1-800-835-3278 • www.coleman.com

MADE IN CHINA • PRINTED IN CHINA

© 2008 The Coleman Company, Inc.

Coleman®, , , and Weathermaster® are registered trademarks of

The Coleman Company, Inc.

4010003995 (20081030)

STITCH LINE