Hinged, Rigid Door (continued)
2. | Insert end of Vertical Door Pole into |
| bottom hinge plate, apply pressure to |
| form a slight bow, then insert other tip |
| of pole into top hinge. Zip up vertical |
| sleeve. (Fig. 13 & 14) |
3. | Assemble Door Pole (longer black pole |
| with plastic cap tips); then insert into |
| zippered sleeve at top of door. (Fig. 15) |
4. | Insert end of Door Pole into top hinge |
Fig. 13
Fig. 14
Attaching Room Divider
1.Divider Panel can be installed through center of the tent by inserting toggles through the
top and bottom fabric loops as shown.
(Fig. 23 & 24)
Fig. 23
Top
Fabric
Loops
Divider
Panel
Fig. 24
plate, apply pressure to form a bow, |
then insert other tip of pole into the |
bottom hinge. (Fig. 16) |
5. Zip up sleeve to enclose Door Pole. |
(Fig. 17) |
Pole Sleeve
Fig. 17
Pole
Sleeve
Fig. 15
Fig. 16
Electrical Cord Access | Fig. 25 |
1.Unzip access panel in the lower left corner of tent and bring in electrical cord.
NOTE: Use only UL approved cords rated for outdoor usage. (Fig. 25)
Cooler Access
The smaller zippered opening at the side of tent is designed for added ventilation and easy access to your beverage cooler.
1.To use as a vent, unzip flap to expose screen.
2.To use as a cooler access, unzip other flap to make an avenue to bring
beverages into tent. (Fig. 26)
To Attach Rainfly
1.Drape Rainfly over tent. Make sure seams on Rainfly are facing down and centered over poles of the tent. (Fig. 18) NOTE: Hook and loop fasteners, located on seams of under - side of rainfly, should be centered over black and gray poles.
Rainfly
Fig. 18
2.Locate all hook & loop fasteners on underside of Rainfly and wrap around each Leg Pole and Window Vent Pole locations. (Fig. 19)
3.Insert metal hook on elastic straps on Rainfly into the hole on each Leg Pole. (Fig 20 & 21)
Center Leg |
|
Pole | End Leg |
Location | |
| Pole |
| Location |
Fig. 19 |
| Fig. 20 |
| Fig. 21 |
|
|
|
|
|
4.Loop ends of guylines over stakes, stretch tight, then hammer into ground at an angle as shown. (Fig. 22 & 22A)
Guyline
22A
Fig. 22
To Store
1.All poles and stakes must be placed in the storage bag to prevent damage to the fabric items placed in the carry case.
2.Make sure tent is clean and dry before placing in carry case.
3.Remove rainfly, spread out on floor of tent, then unzip door & vents before taking tent down for storage.
4.Neatly fold tent to width of pole storage bag, place on tent, roll tightly, and place in carry case.
5.Store in a clean, dry area.
Things You Should Know:
•Under certain conditions (cold weather, high humidity, etc.) condensa- tion will form on the inside of your tent. Condensation is caused by water vapor from your breath, perspiration, or any wet clothing inside the tent. It is NOT LEAKAGE through the tent fabric. It can be minimized by removing wet clothing from your tent and by providing good ventila- tion through the tent.
•Tree limbs, tree sap, bird droppings, or moisture steadily dripping off tree limbs can cause damage to the tent fabric and its coating resulting in leaks or loss of
•Never store tent, even for a short period of time, without drying it thoroughly and brushing off caked dirt. Do not pack stakes or poles inside your tent. Use a separate storage bag.
•Stakes should be removed by pulling on the stake itself. NEVER PULL ON THE TENT TO REMOVE STAKES AS THIS COULD RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY.
•Tent poles should not be left telescoped together during storage.
•Do not leave your tent
WARNING: Keep all flame and heat sources away from this tent fabric.
This tent meets the flammability requirements of
The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219
MADE IN CHINA • PRINTED IN CHINA
© 2008 The Coleman Company, Inc.
Coleman®, 
, 
, and Weathermaster® are registered trademarks of
The Coleman Company, Inc.
4010004006 (20081009)
STITCH LINE
