WEATHERMASTER® 10 TENT MODEL 2000001598
STITCH LINE
Before you begin
Read all instructions before set up.
•Select a level site clear of rocks, branches, and other hard or sharp objects, to install your tent.
WARNING: Keep clear of overhead power lines.
•Do not set up your tent under trees because of potential lightning strikes or falling tree limbs in inclement weather.
•Secure with all stakes and guylines provided to prevent property damage or personal injury.
•For best results in windy conditions, position narrow end of tent into the wind.
•Enlist the help of at least one other person to assist you when it is time to assemble the tent.
Pole Descriptions
Description | Qty. | Pole | Pole | Pole |
Dia. | Repair Kit | Replacement Kit | ||
Long Leg Pole, steel |
|
|
|
|
(w/ red marking) | 2 | 19mm | N/A | 5010000614 |
Short Leg Pole, steel | 4 | 19mm | N/A | 5010000623 |
Curved Ridge Pole, steel |
|
|
|
|
(w/ red marking) | 1 | 19mm | N/A | 5010000613 |
Curved Ridge Pole, steel | 2 | 19mm | N/A | 5010000615 |
Side Window Pole, black, |
|
|
|
|
fiberglass, metal tips | 2 | 8.5mm | 5010000541 | 5010000547 |
Door Pole, long, thin ,black, |
|
|
|
|
fiberglass, rubber tips | 1 | 6.3mm | 5010000543 | 5010000545 |
Vert. Door Pole, short, black, |
|
|
| |
fiberglass, rubber tips | 1 | 6.3mm | 5010000543 | 5010000545 |
To Set Up Tent
1.Unfold tent and spread out on a clean, level surface with the door facing the desired direction. Unzip doors. (Fig. 1)
Fig. 1
Door
2. Pull four corners of tent taut, then secure by driving stakes through web loops at an angle for better anchoring. (Fig. 2)
Fig. 2 |
6.Rotate all six Leg Poles upright and insert
pin on each web loop at the side locations | 7A |
as shown. (Fig. 7 & 7A) | Pin |
|
7B |
Fig. 7 |
Metal Tip 
Sleeve | Hole in | |
Leg Pole | ||
|
Window Pole
7C
6.Assemble the two,
7.Insert tapered metal tip on Window Pole into Leg Pole. NOTE: It may be necessary to gently rotate Leg Pole so the hole will line up with the Window Pole.
8.Go to opposite end of each window pole and gradually apply
pressure to the pole forming an arch. Insert the pin into the leg pole end at the corners of tent. (Fig. 7 & 7C)
9. Locate the plastic hooks at sides and corners of tent, then snap onto Leg Poles to attach. (Fig. 8)
10. Locate web strapFig. 8Fig. 9 with plastic hook on
the sides of each end panel Window Vent, then snap onto the corner Leg Pole. (Fig. 9)
3. Assemble three, steel, |
|
|
| Fig. 3 | |
curved Ridge Poles. Insert Ridge Pole |
|
|
|
|
|
| Ridge Pole | ||||
|
|
|
| ||
(with red marking) into center sleeve |
| with Red |
|
|
|
| Marking |
|
|
| |
on top of tent with the red trim (Fig. 3). |
|
|
|
|
|
Insert the remaining curved Ridge Poles |
|
|
|
|
|
|
|
| Sleeve | ||
into the other two sleeves on top of tent. |
|
|
| with Red |
|
|
|
| Trim |
| |
|
|
|
|
| |
4. Assemble six, steel,
NOTE: Make sure steel button locks
into third hole on pole as shown. (Fig.4) 5. Insert curved end of Leg Poles
(with red marking) into the ends of the Ridge
11.To stretch tent to finished size:
•Push in button on Leg Pole while twisting lower Leg Pole section counterclockwise (Fig.10);
•Pull up on top Leg Pole section until tent is taut;
•Twist the lower Leg Pole clockwise until the button locks into the center
or lowest hole;
• Repeat on remaining Leg Poles.
12.Insert plastic stakes through web straps located on both sides of tent, then drive in to secure. (Fig. 11)
Button 
Center Hole
Lower Hole
Lower
Leg Pole
Section
Pole (with red marking). Insert curved end of remaining short Leg Poles into the ends of the remaining Ridge Poles. (Fig. 5 & 6)
Ridge Pole with Red Marking in center sleeve
Hinged, Rigid Door |
|
|
| Fig. 12 |
| Sleeve |
| ||
1. Assemble Vertical Door Pole (shorter |
|
|
|
|
|
|
|
|
black pole with plastic cap tips); then insert through zippered sleeve on side of door and into hinge. (Fig. 12)
Hinge 
(continued on other side)
