Coleman 2000005748 To Attach Rainfly, Self-rolling Windows, Attaching Room Divider, Cooler Access

Awning Pole

To Attach Rainfly

1.Drape Rainfl y over tent. Make sure seams on Rainfl y are facing down and centered over poles of the tent. (Fig. 17)

NOTE: Hook and loop fasteners, located on seams of underside of Rainfl y, should be centered over Ridge Poles.

Self-rolling Windows (continued)

CAUTION: All “springs” must be removed from sleeves before tearing down tent to avoid damage to the tent fabric or part. To avoid injury, carefully roll up “springs”. Keep out of reach of children. Store rolled “springs in bag with stakes.

Rainfly

Sleeve

Door

		Fig. 17
2. Assemble thin, black, shock-corded Awning
	Awning	Fig. 18
	Pole

Attaching Room Divider

1.Divider Panel can be installed through center of the tent by

inserting the toggles through top and bottom fabric loops as shown.

(Fig. 29 & 30)

Fig. 29

Top

Fabric

Loops

Divider
Panel	Fig. 30

Pole with metal tips; then insert through
sleeve in Rainfly above door. Repeat the
process to install the awning pole at the	Sleeve

opposite side of the tent. (Fig. 18)

3. Insert tapered metal tip on Awning Pole	Grommet
into grommet located on web strap

clipped to center Leg Pole. (Fig. 19)

4.Go to opposite center Leg Pole on other side of door and gradually apply

pressure to the pole forming an arch.	Fig. 19
Insert metal tip into the grommet.
	Fig. 20
5. Locate all hook & loop fasteners on underside of
Rainfl y and wrap around Leg Poles and Awning
Pole locations. (Fig. 20)

6. Insert metal hook
		Center
onelastic straps on		Leg Pole
		Location
Rainfl y into the hole on			End Leg
each Leg Pole.			Pole
			Location
(Fig. 21 & 22)	Fig. 21
				Fig. 22

7.Loop ends of guylines over stakes, stretch tight, then hammer into ground at an angle as shown. (Fig. 23 & 23A)

Fig. 23

Guyline

23A

Self-rolling Windows
CAUTION: “Springs” may have sharp edges. Handle with care to avoid injury.
Keep out of reach of children.
NOTE: Carefully unroll metal “springs” stored in bag with stakes. The color
marking on each “spring” should match the color of the fabric “fl ag” sewn to
the window or door sleeve opening. (Fig. 24)				Color “Flag”
1. Locate sleeve(s) in window panel, open hook & loop
fastener; then insert “spring(s)” with matching color				Sleeve
marking. (Fig.24 & 25)
				Fig. 24
NOTE: When inserting into the sleeve(s), the color mark-
ing on the “spring(s)” should always face the operator.
2. Close hook & loop fastener to secure.				Color
3. Before unzipping and opening the window, push in at
				“Flag”
top to engage “spring(s)” to activate the self-rolling
feature. (Fig. 26)				Color
4. Unzip to allow the window panel to roll down automati-				Dot
cally; zip back to close window panel. (Fig. 27 & 28)				Fig. 25
NOTE: Repeat steps above for inserting the color
matching “spring(s)” into sleeve(s) for the rest of
the windows.				Push in at top to
				engage “spring(s)”
Fig. 26	Door	Window Panel
	Window
	Panel
		Sleeves	Fig. 27	Fig. 28

Electrical Cord Access Fig. 31

1.Unzip the access panel in the lower left corner of tent and bring in an electrical cord.

NOTE: Use only UL approved cords rated for outdoor usage. (Fig. 31)

Cooler Access

The smaller zippered opening at the side of tent is designed for added ventilation and easy access to your beverage cooler.

1.To use as a vent, unzip fl ap to expose screen.

2.To use as a cooler access, unzip other fl ap to

make an avenue to bring beverages into tent.	Fig. 32
(Fig. 32)

To Store

1.All “springs” must be rolled up and placed in bag with stakes.

2.All poles and stakes must be placed in the storage bag to prevent damage to the fabric items placed in the carry case.

3.Make sure tent is clean and dry before placing in carry case.

4.Remove rainfl y, spread out on fl oor of tent, then unzip door & vents before taking tent down for storage.

5.Neatly fold tent to width of pole storage bag, place on tent, roll tightly, and place in carry case.

6.Store in a clean, dry area.

Things You Should Know:

•Under certain conditions (cold weather, high humidity, etc.) condensation will form on the inside of your tent. Condensation is caused by water vapor from your breath, perspiration, or any wet clothing inside the tent. It is NOT LEAKAGE through the tent fabric. It can be minimized by removing wet clothing from your tent and by providing good ventilation through the tent.

•Tree limbs, tree sap, bird droppings, or moisture steadily dripping off tree limbs can cause damage to the tent fabric and its coating resulting in leaks or loss of fl ame-resistant properties.

•Never store tent, even for a short period of time, without drying it thoroughly and brushing off caked dirt. Do not pack stakes or poles inside your tent. Use a separate storage bag.

•Stakes should be removed by pulling on the stake itself. NEVER PULL ON THE TENT TO REMOVE STAKES AS THIS COULD RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY.

•Tent poles should not be left telescoped together during storage.

•Do not leave your tent set-up for weeks at a time. Be aware that exposure to ultraviolet rays from the sun can seriously damage material and/or cause it to become discolored.

WARNING: Keep all flame and heat sources away from this tent fabric. This tent meets the fl ammability requirements of CPAI-84. The fabric may burn if left in continuous contact with any fl ame source. The application of any foreign substance to the tent fabric may render the fl ame-resistant properties ineffective.

The Coleman Company, Inc. • 3600 North Hydraulic • Wichita, Kansas 67219

1-800-835-3278 • www.coleman.com

MADE IN BANGLADESH • PRINTED IN BANGLADESH

© 2009 The Coleman Company, Inc. All rights reserved.

Coleman®, , and Weathermaster® are registered trademarks of

The Coleman Company, Inc.

4010007331 (20091022)

STITCH LINE