Compex Systems PS2208B Specifications, 5. Installation of PS2208B, WARRANTY REGISTRATION CARD, Industrial Standards, Interface, Link Distance, 100Base-TX:, 10Base-T:, LED Indicators

4.	Specifications
Industrial Standards		Complies with IEEE 802.3 10Base-T, IEEE
		802.3u 100Base-TX and ANSI/IEEE 802.3
		N-Way auto-negotiation standards; FCC
		Class A; CE mark.
Interface		Each unit has eight 10/100Mbps UTP ports
		(RJ-45).
Port Speed/Mode Selection		Auto-negotiation
Link Distance		100Base-TX:can support up to 100M of
		‘Category 5’ UTP cable to PC, Hub or
		another Switch.
		10Base-T:can support up to 100M of
		‘Category 3, 4, and 5’ UTP cable to PC, Hub
		or another Switch.
LED Indicators		LED indicators are provided for status
		monitoring. These include LEDs for system
		power, port speed, traffic activity and link.
Dynamic memory sharing		128K bytes
In/Out buffer
Forwarding Method		Store-and-Forward.
Number of MAC Addresses		1K MAC Addresses
Dynamic Addresses		Yes.
Learning / Filtering
Environment Requirements
Temperature:		Operating: 0°C to 40°C
Humidity:		Storage: -5°C to 60°C
		Operating: 10% RH to 90% RH
		(non-condensing)
Physical Dimensions		151 x 92 x 25mm (L x W x H)
Safety		UL, CSA, TUV/GS

5. Installation of PS2208B

PS2208B can be installed on a flat surface (desktop) or mounted on a wall. Follow the steps below for proper installation.

Desktop installation

1.Unpack the switch.

2.Choose a location near the devices to be connected and close to an electrical outlet. Preferably placed the switch on a desktop or any other clean, smooth, level and sturdy surface.

3.Ensure that there is enough clearance around the unit to allow attachment of network cables, power adapter and allow air circulation.

4.Connect the power adapter that is supplied in the package to the switch. The POWER LED and PORT LED for each connected port should be lighted up.

Wall installation

1.Measure the distance between the mounting holes at the bottom of the switch and mark the wall to match the location of the mounting holes on the switch.

2.Drill pilot holes at the two marked locations.

3.Fix two 5/16-inch diameters flat-head mounting screws into the wall, with the heads of the screws protruded 1/8 inch out from the wall.

4.Carefully set the switch over the screws in the wall; then slide the switch down onto the screws, pressing it slight to the wall.

5.Connect the power adapter that is supplied in the package to the switch. The POWER LED and PORT LED for each connected port should be lighted up.

This document may become superseded, in which case you may find its latest version at: http://www.compex.com.sg/prodspec.asp?f=Manual&s=1

Disclaimer: Compex, Inc. provides this guide without warranty of any kind, either expressed or implied, including but not limited to the implied warranties of merchantability and fitness for a particular purpose. Compex, Inc. may make improvements and/or changes to the product and/or specifications of the product described in this guide, without prior notice. Compex, Inc will not be liable for any technical inaccuracies or typographical errors found in this guide. Changes are periodically made to the information contained herein and will be incorporated into later versions of the guide. The information contained is subject to change without prior notice.

Trademark Information: Compex®, ReadyLINK® and MicroHub® are registered trademarks of Compex, Inc. Microsoft Windows and the Windows logo are the trademarks of Microsoft Corp. NetWare is the registered trademark of Novell Inc. All other brand and product names are trademarks or registered trademarks of their respective owners.

Notice: Copyright © 2004 by Compex, Inc. All rights reserved. Reproduction, adaptation, or translation without prior permission of Compex, Inc. is prohibited, except as allowed under the copyright laws. Manual Revision by Ong

Manual Number: M-0311-V1.6CVersion 1.6, July 2004

FCC NOTICE: This device has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, the user is encouraged to try to correct the interference by one or more of the following measures:

•	Reorient or relocate the receiving antenna.	•	Increase the separation between the
•	Connect the computer into an outlet on a	•	computer and receiver.
	circuit different from that to which the		Consult the dealer or an experienced
	receiver is connected.		radio/TV technician for help.

Caution: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment.

FCC Compliance Statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2)This device must accept any interference received, including interference that may cause undesired operation.

ICES 003 Statement

This Class A digital apparatus complies with Canadian ICES-003

DECLARATION OF CONFORMITY: Compex, Inc. declares that the product:
Product Name: Compex Fast Ethernet Desktop Switch
Model No.: PS2208B conforms to the following Product Standards:
Radiated Emission Standards: EN55022A, FCC Part 15 Class A
Conducted Emission Standards: EN60555Pt2 conducted emission; EN55022A conducted emission,
LVD 60950 standard, FCC Part 15 Class A
Immunity Standards: IEC 801-2; IEC 801-3; IEC 801-4
Low Voltage Directive: EN 60 950:1992+A1: 1993+A2: 1993+A3; 1995+A4; 1996+A11: 1997.
Therefore, this product is in conformity with the following regional standards: FCC Class A 
following the provisions of FCC Part 15 directive; CE Mark  following the provisions of the EC
directive.
Manufacturer’s Name: Compex, Inc.	European Contact & Technical Support
Address: 4051 E. La Palma, Unit A,	ReadyLINK Networktechnology GmbH,
Anaheim, CA 92807, USA	Albert Einstein Straβe 34/M21,
	63322 Rödermark, Germany
	Fax: ++49 (60) 749-0668

----"

-----Cut along the dotted line-----"-----

Cut along the dotted line-----

"-----

Cut along the dotted line-----

"----

line-----

WARRANTY REGISTRATION CARD

dotted

[M-0088-V2.3C]

the

You can register via Internet at:

http://www.cpx.com

or http://www.compex.com.sg

along

Or E-mail:support@compex.com.sg

with the following information:

Cut

To activate the warranty, please complete this card and return to Compex within ninety (90) days of

purchase date.

------

Product:

Purchase Date:

Revision:

Serial No:

Name:

Title:

E-mail:

------line"

Company:

Dept:

Address:

City:

Postal/Zip Code:

State:

Country:

dotted

Phone: (

)

Extn:

Fax: (

)

Computer in

which this

product

is

Model:

Serial No:

the

installed?

Network

! TCP/IP

! IPX/ODI

! XNS

! OST

! DLC

! DECnet

along

protocol (Check

! NDIS

! SNA

! NBP

! Other:

------Cut

all that apply):

Network

Novell NetWare: ! 3.X

! 4.X

! 5.X

SCO Unix: ! Openserver Ver:

Operating

Microsoft Windows: ! NT4.0

! 95

!

98

! Win 2000

System

(Check

Linux: ! Red Hat Ver:

! SUSe Ver:

! Others:

Ver: .

line------"

all that apply):

Others NOS:

Ver:

.

Applications

used

on

! Desktop Publishing

! Word Processing

! Accounting

network processing

! CAD/CAM

! Spreadsheet

!

Database Management

dotted

(Check all that apply):

! E-mail

! Other:

How did you

! Work

! Friend

! Internet

! Dealer

! Magazine

! Exhibition

the

learn

about

! Other:

Compex?

along

Note:

------Cut

For purchases within U.S.A and Canada, please fax to Compex, Inc. at (714) 630-6521

For purchases outside U.S.A and Canada, please fax to Compex Systems Pte Ltd at (65) 6280-9947

line------"

--------Cut along the dotted