IMPORTANT SAFETY
INSTRUCTIONS
WHEN USING ELECTRICAL APPLIANCES, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE TAKEN, INCLUDING THE FOLLOWING:
Read all instructions before using APPLIANCE. Keep away from water
DANGER
1.Unplug from outlet before putting on or taking off parts.
2.This mirror should not be used by or near children or individuals with certain disabilities.
3.Use this mirror only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.
4.Never operate this mirror if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the mirror to a service center for examination and repair.
5.Keep the cord away from heated surfaces.
6.Never drop or insert an object into any opening.
7.Do not use outdoors.
8.Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
9.To disconnect, be sure mirror is in the off position, then remove plug from outlet.
10.Do not leave appliance unattended when it is plugged in.
11.Be sure mirror is not in a position where it can reflect sunlight; reflected sunlight can cause fire.
12.Do not use on a soft surface such as a bed, where openings may be blocked.
13.Touch knob on mirror base until light shuts off. Allow unit to cool and unplug cord before replacing light bulbs.
14.Do not place or store appliance where it can fall or be pulled into a tub or sink.
15.If an appliance falls into water, unplug it immediately. Do not reach into the water.
16.To protect against electrical hazards, do not use while bathing or in the shower.
17.Never use while sleeping.
18.Do not use a bulb greater than 13 watts.
Use on any 120 volt 60 hertz AC electric outlet (ordinary house current). Do not use it on any other electrical outlet.
FOR HOUSEHOLD USE ONLY
SAVE THESE
INSTRUCTIONS
OPERATING
INSTRUCTIONS
To reduce the risk of electric shock, this mirror has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit contact a qualified electrician to install the proper outlet. Do not change the plug in any way.
CAUTION: Be sure direct sunlight does not strike mirror when left unattended; reflected sunlight can cause fire.
1.Your lighted makeup mirror will rotate 350° so that you can use either the normal, flat mirror or the 8x magnifying mirror located on the opposite side.
2.Plug into any standard 120
volt wall outlet. The mirror light is activated by touch. Touch the base to turn light on or off.
3.After use, always touch the knob on the base to turn the mirror to the OFF position and unplug.
4.The beauty and design of this mirror complement any decor. Therefore, you may wish to leave the mirror displayed. However, if you choose to store the mirror, see section about storage for detailed information.
Special Feature
This lighted makeup mirror uses a fluorescent bulb. The bulb lasts up to 10,000 hours and does
not require replacement. In the unlikely event that the bulb does need replacement, follow the instructions below.
Replacing Fluorescent Tube Lamp
Caution: Turn off power and unplug mirror. Allow to cool at least three minutes before replacing fluorescent tube lamp. Replace tube lamp only with tube lamp of same wattage rating. Remove tube lamp with care to avoid breakage.
Replacing Fluorescent Tube Lamp
1. This mirror uses a 13W maximum 120V type
2. Remove screws from left and |
|
right sides of mirror. (See Fig. 1.) | Fig. 1 |
|
3.Carefully lift off the removable housing from the half that is affixed to the stand.
4.A cable tie is used to
protect the fluorescent tube |
| |
lamp during transportation. To |
| |
replace the fluorescent tube |
| |
lamp, you must first cut the |
| |
cable tie. While holding the |
| |
socket, pull the fluorescent | Fig. 2 | |
tube lamp out of the socket | ||
| ||
with care to avoid breakage. |
| |
(See Fig. 2.) Align the metal |
| |
pins on the fluorescent tube |
| |
lamp with the holes in the |
| |
socket and push gently to |
| |
secure. (See Fig. 3.) After |
| |
the fluorescent tube lamp is |
| |
replaced, there is no need to | Fig. 3 | |
replace the cable tie. |
|
5.Carefully replace the removable half after locating and aligning the screw holes to the fixed half.
6.Insert screws into screw holes and tighten.
