HALO L630 2C 2N POWER TRAC INSTALLATION INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

When installing or using this track system, basic safety precautions should always be followed, including the following:

1.Read all of these instructions before installing the track system.

2.Save these instructions and refer to them when additions to or changes in the track configuration are made.

3.Do not install this track in damp or wet locations.

4.Do not install any part of a track system less than 5 feet above the floor.

5.Do not install any fixture assembly closer than 6 inches from any cur- tain or similar combustible material.

6.Disconnect electrical power before adding to or changing the config- uration of the track.

7.Do not attempt to energize anything other than track lighting fixtures on the track. To reduce the risk of fire and electric shock, do not attempt to connect power tools, extension cords, appliances and the like to the track.

8.CAUTION: This track system is not intended for use with power sup- ply cord or convenience receptacle adapter.

9CAUTION: To reduce the risk of fire and electric shock, use only fix- ture assemblies marked for use with Halo track and track fittings marked for use with L630 Series track.

10.The track system is to be supplied by one or two 480V/277V 60Hz single phase 3-wire system with a grounded neutral.

11.The mounting clips, screws or stems are to be mounted in pre-drilled holes as follows:

4’ Track - two places - one at each end of track

8’ Track - Three places - one in the center and each end of the track 12’ Track - four places - one at each end of track and 4 feet from each end

If track requires field cutting, refer to field cutting instructions

12.CAUTION: The maximum capacity of L630 Track is 40A per circuit. When installing, do not exceed the capacity of your circuits. Check fuses and circuits carefully before installing.

SAVE THESE INSTRUCTIONS

INSTALLATION OF TRACK TO AN OUTLET BOX

Step 1. Punch out proper knockout holes in ceiling plate for mounting to out- let box and to live end fitting (note that special smooth plastic finish piece on metal ceiling plate requires caution in deterring location of proper knockout before making holes). Remove flat head screw)s) from back of live end fitting and use to fasten plate to fitting.

Step 2. Remove cover from live end fitting. Place track with ceiling plate attached over outlet box and mark on ceiling or wall the position of the track mounting holes.

Step 3. Drill mounting holes large enough for toggles and install track with fur- nished toggle bolts. If track is to be mounted on a solid surface, use #8 screws (not supplied) instead of toggle bolts.

Step 4. Fasten ceiling plate to outlet box with two screws. Pull wires from box through open hole in live end as shown.

Step 5. Cut and strip wires from box and fasten to screw terminals in live end fitting (see detail). Push excess wire back into outlet box.

Step 6. Replace cover on live end and tighten screw.

Figure 1

NEUTRAL

LINE

 

 

GREEN

 

 

TIGHTEN SCREW

TRACK

GROUND

NEUTRAL

LINE

AFTER INSERTING

 

SCREW

 

 

IN TRACK

 

OUTLET

BOX

OUTLET

BOX

COVER

LIVE END

CONNECTOR

MOUNTING

SCREWS

COVER

SCREW

Cooper Lighting • 1121 Highway 74 South • Peachtree City GA 30269 • 770-468-4800 703113

Page 1 Page 2
Page 1
Image 1
Cooper Lighting important safety instructions Halo L630 2C 2N Power Trac Installation Instructions
Page 1 Page 2

L630 2C 2N specifications

Cooper Lighting has long been a leader in the development of advanced lighting solutions, and the L630 2C 2N model exemplifies their commitment to innovation and performance. The L630 series is designed for both commercial and industrial applications, providing versatile and energy-efficient lighting options that meet the needs of various environments.

One of the main features of the Cooper Lighting L630 2C 2N is its superior energy efficiency. Utilizing the latest LED technology, this model significantly reduces energy consumption compared to traditional lighting systems. The longevity of LED lights means less frequent replacements, contributing to lower maintenance costs and minimal downtime in industrial settings. The L630 series has a remarkable lifespan, often exceeding 50,000 hours, making it a cost-effective solution for long-term use.

The L630 2C 2N also boasts a robust design, built to withstand the rigors of demanding environments. With a durable housing constructed from high-quality materials, this lighting solution is resistant to dust and moisture, making it ideal for warehouses, manufacturing plants, and outdoor spaces. Its design ensures reliable performance under various conditions, providing consistent light output where it’s needed most.

This model features versatile mounting options, allowing for easy installation in a variety of settings. Whether suspended from ceilings, wall-mounted, or used in modular configurations, the L630 2C 2N can be tailored to fit specific spatial constraints and lighting requirements. This adaptability makes it a popular choice among facility managers looking to optimize their lighting layouts.

In terms of technological advancements, the L630 series integrates smart lighting controls that enhance functionality and user experience. These controls support features like occupancy sensing and daylight harvesting, which automatically adjust lighting based on real-time conditions, further improving energy efficiency and user comfort.

Additionally, the L630 2C 2N offers excellent optical performance, providing uniform light distribution with minimal glare. This characteristic enhances visual comfort for those working or spending time in illuminated areas, promoting productivity and safety.

Overall, Cooper Lighting’s L630 2C 2N model combines energy efficiency, durability, versatility, and advanced technology, making it an exceptional choice for a wide range of lighting applications. Its thoughtful design and innovative features ensure that it meets the evolving needs of modern commercial and industrial spaces.
Top Page Image Contents