Cooper Lighting E3AASR, PN3MR manual , 

C A T A L O G # :			T Y P E :
 
Specification grade, wet listed 71 watt			
				 
MR16 lamp adjustable fixture.			
Adjustment mechanism features hot			
aiming capability, aiming marks and too-
			
less locking. Optics provide glare-free
			
50° cutoff to lamp and lamp image. For
use with all halogen MR16 lamp vari-			
eties. Units small size is ideal for tight			
	
construction areas. Insulation must be				
kept 3" away from sides and top of fix-		3 1/2"
ture. Optical element can be changed		[89mm]
		4 3/8"		
after installation to provide a variety of
		[112mm]	Note: O.D. on SF
distributions. e.g. into a Downlight		5 1/8"		
			is 4 7/8"
		[130mm]
    

.. . Re fl e c t or		M3 grade grain oriented silicon steel complete with
.040 thick aluminum spun parabolic interior		an integral thermal to protect against overheating.
reflector in Clear, Gold, Haze, Warm Haze, Black		For dimming, use dimmers rated for electromagnet-		      
Alzak® finish	.	ic transformers. Transformer is warranted for 5
Special cone colors listed below.		years and is serviceable from below ceiling.
 .. . Gl a s s		Note: If a dimming system is operated for con-	3 "	A D J U S T A B L E
.125 thick tempered clear glass protects lamp		struction lighting in its "shunt" mode, i.e. bypass-		S H O W E R
		ing the dimmer modules, for an extended period of
from direct spray of water and is retained during
		time, fixtures with the dual-tap toroidal transformer
relamping.
		should be operated on the "Switched Fixture" out-
 .. .F la nge
		put until the dimmers are in use. Operating fixtures
Self flange reflector or die-cast flange with either		on the "Dimmed Fixture" output with a full 120v
matte white or clear coat finishDie-cast flanges		input for an extended period will overdrive the			5"
are easily removed for field painting. Elements are		lamp and cause shortened lamp life.			[127mm]
keyed for proper insertion.			4 3/8"		8 5/8"
.. . Ad jus ta b il it y		 .. . F r a m e / H ou s i ng
			11 7/8" [112mm]		[220mm]
Removable lamp adjustment mechanism provides		Hot dipped galvanized 20 gauge steel frame	[302mm]
		with built in 1/2 inch plaster lip. Gunsights allow
up to 45° tilt and 361° rotation and locks into any
		for consistent alignment.
aiming position. Unit is relamped without unlocking					Ceiling Cutout:
					4 3/8" [112mm]
adjustments. Translating centerbeam optics maxi-		 .. . J unc ti on B ox
mize light output.		18 cubic inches, listed for 4#12 AWG or 6#14
.. . L e ns		AWG 90° C additional feed through conductors,
Soft focus lens standard for smooth beam		has three 1/2" pryouts.
patterns. Up to two filter media can be used		 .. . B a r H a n ge r s
which are retained during relamping.		No Flex® bar hangers with positive locking, for
 .. .At ta c hm e nt		use with wood, engineered wood and steel frame
Positive torsion springs pull flange tight to ceiling.		joists spaced up to 24" O.C. ship with platform.
		For use in T-bar ceilings order accessory push on
Mechanical light trap eliminates spill light at edge
		clips. Nailess barb and locator lip provide consis-
of flange or reflector.
		tent installation height.
.. . So c k e t			E N E R G Y D A T A
		 .. . C od e s
GX5.3 base for Bi-pin MR16 lamps. Back light			120V Input
shield keeps interior of fixture dark.		Thermally protected, IP labeled. Unit is airtight and	Lamp	Input	Operating
		exchanges less than 2.0 CFM with the plenum at a
 .. .T r a ns for m e r			Watts	Watts	Current
		pressure of 75 pascals. Insulation must be kept
™			20	23	.19
Truvolt toroidal transformer with dual-output taps		three inches away from fixture sides and none on
			35	41	.34
for proper 12.0V operation and quiet operation
		top as to entrap heat.
when dimmed. Dimmer tap compensates for inher-			37	42	.35
		 .. . L a be l s
ent voltage loss from dimmers, resulting in 30%			42	47	.39
more lumens than traditional laminated transform-			50	57	.48
ers. Toroidal design, with 90% or greater efficien-			65	70	.58
cy, features a rolled one-piece continuous core of			71	77	.64
			75	81	.68

 

S A M P L E N U M B E R : P N 3 M R - E 3 A A S R C

Complete unit consists of a platform and element

	O p t i c a l
P l a t f o r m	E l e me n t	F i n i s h


F l a n g e A c c e s s o r i e s

PN3MR = 3" Non-	E3AASR
IC Low Voltage	= 3"
Housing	MR16
PN3MR REMOTE =	0 - 45°
3" Non-IC Housing	Adjustable
for Remote	Accent
	Lensed
Transformer
	Reflector
 

Standard	White	BU=Blush
C=Clear	Custom	Custom Cont.
H=Haze	K=Cognac	BUH=Blush
G=Gold	KH=Cognac	Haze
WMH=Warm	Haze	GP=Graphite
Haze	CC=Chocolate	GPH=Graphite
W=Gloss White	Custom	Haze
B= Black	CCH=Chocolate	PN=Pine
MW= Matte	Haze	PNH=Pine Haze
		SK=Sky

Blank= White die-cast

SF= Self Flange

SFWF= Self Flange Painted White

RAW= Natural Die Cast

MBCLP = 40	Spread Lens
Push On T Bar	L-UV = UV
Clips (for 10	Reduction Lens
Units)	L-LPINK =
PLE3 = Plaster
	Light Pink
Lip Extension	L-LSTRAW =
for Max 2"
	Light Straw
Thick Ceiling
	Lens
L-SPD =
	L-27K =
Spread Lens
	2700K dichroic
L-LNR = Linear
	filter

L-DAY =

Daylight Lens

L-SPINK =

Surprise Pink

Lens

L-PLAV = Pale

Lavender Lens

L-HEX= Hex

Cell Louver

SKH=Sky Haze

For additional options please consult factory.

Matte white is recommended for self flanged reflectors

ADI042551