SECTION V - MAINTENANCE AND STORAGE

IMPORTANT: The knife should be checked for sharpness and the nuts and bolts attaching it to the flywheel for tightness every 8-10 hours of operation.

IMPORTANT: Every time you perform maintenance or any kind of service or check on the knife, be sure to check the gap between the knife and wear plate for proper setting.

NOTE: A knife gauge has been provided with your machine. It is 1/16th” thick and should be used to set the correct gap between the knife and wear plate.

If the cutting mechanism strikes any foreign object or if your machine should start making an unusual noise or is vibrating, stop the engine, disconnect the spark plug wire from the spark plug. Allow the engine to cool before you;

a.Inspect and examine for obvious damage.

b.Check for loose parts, bolts, and nuts.

1.When not in use, your chipper should be stored out of the reach of children. Be sure there are no gasoline fumes in the storage area. For long periods of storage (over winter), refer to the engine owner’s manual.

2.After every 8 hours of operation, lubricate the chipper side and drive side bearings with multi-purpose lithium grease. Also, check the bearing collar set screws regularly to be sure they are tight. If they are loose, reset them with Loctite 243, obtainable at any hardware store.

3.You will find information included referring to operation and maintenance of the chipper engine. Look it over carefully. BE CERTAIN TO SERVICE THE ENGINE BEFORE YOU START IT.

4.When the steel chipping knife (item #21, pg. 30) needs replacing or sharpening, refer to the section on removal, sharpening and re-installation.

5.Care must be exercised when sharpening the knife to maintain the correct bevel and a straight edge. Refer to sharpening directions. When you install a knife, the clearance between the knife and wear plate must be checked and set. This clearance or gap should be set to 1/16” (see figure 1).

6.To adjust this clearance, loosen the three ¼” nuts and bolts (item #16 & #22, pg. 30) holding the wear plate in place. The wear plate can be slid up or down (in or out) to achieve the correct gap setting.

7.Take the knife gauge and slide between the knife and wear plate. If the gap is set correctly, the knife gauge will lightly touch both the knife and wear plate. If the gap is too small, you will not be able to get the gauge between the knife and wear plate. If the gap is too large, there will be excess room between knife gauge, knife and wear plate. Tighten the nuts and bolts when the wear plate is in the correct position. Be certain the flywheel rotates without hitting anything before starting the chipper.

8.If the gap between the wear plate and the knife is not set correctly, you will have excessive vibration when chipping and the blade will seem to be dull. This should be checked every 8-10 hours of operation.

9.If at any time it becomes necessary to disassemble the chipper for repairs, the chipper disk (item #13, pg. 30) must be re-installed in exactly the same position on the rotor shaft.

NOTE: Proper gap setting is critical to the proper operation of your machine.

17

Page 16 Page 18
Page 17
Image 17
Country Home Products C123E-CHP instruction manual Section V Maintenance and Storage
Page 16 Page 18

C123E-CHP specifications

The Country Home Products C123E-CHP is a versatile and efficient chipper shredder designed to tackle various outdoor debris, making yard maintenance easier and more sustainable. This powerful machine is particularly well-suited for homeowners who want to manage their garden waste without relying on external disposal methods.

One of the standout features of the C123E-CHP is its robust engine. Equipped with a reliable and durable horsepower motor, it provides the necessary torque to process tough branches, leaves, and other organic materials quickly. The engine is designed for optimal performance, ensuring minimal downtime for maintenance while maximizing energy efficiency.

Another significant characteristic of the C123E-CHP is its dual feed system. The combination of a large chipper chute and a shredding hopper allows users to feed in various sizes of material easily. The chipper chute is ideal for larger branches up to three inches in diameter, while the shredding hopper is designed for softer materials like leaves and small twigs. This dual functionality increases the machine's versatility, catering to a wider range of yard debris.

The C123E-CHP also incorporates advanced cutting technology. The machine comes with hardened steel blades that are not only sharp for clean cuts but also built to withstand wear and tear. This cutting system ensures speedy processing of organic materials and produces finely shredded mulch that can be reused in gardens or flower beds, promoting nutrient recycling.

User safety and convenience are also prioritized in the design of the C123E-CHP. The machine features a protective housing that prevents debris from flying out during operation. This safety feature, combined with easy-access controls and a comfortable handle, enhances the overall user experience. Maintenance is further simplified with easily accessible components, making it convenient for users to clean and service the machine.

In summary, the Country Home Products C123E-CHP is engineered for efficiency, durability, and user-friendliness. Its powerful engine, dual feed system, advanced cutting technology, and safety features come together to create a reliable tool for yard maintenance. This machine not only simplifies the process of managing yard waste but also encourages sustainable practices by turning organic debris into useful mulch for gardens. Whether you're a seasoned gardener or just starting, the C123E-CHP is an invaluable addition to your outdoor arsenal.
Top Page Image Contents