Craftsman 315.115510 Charging a Cool Battery Pack, Applications, Charging the Battery Pack

Models: 11551 315.115510

1 18
Download 18 pages 18.88 Kb
Page 10
Image 10

A WARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury.

A WARNING: Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury.

CHARGING A COOL BATTERY PACK

If battery pack is below normal temperature range, the green LED on charger will come on. Allow battery pack to reach normal temperature, then the red LED will come on.

NOTE: If the charger does not charge the battery pack under normal circumstances, return both the battery

pack and charger to your nearest Sears or other qualified service center for electrical check.

[] Charge the battery pack only with the charger provided.

A

WARNING: Do not use any attachments or accessories not recommended by the manufacturer of this tool. The use of attachments or accessories not recommended can result in serious personal injury.

[] Make sure the power supply is normal household voltage, 120 volts, 60 Hz, AC only.

[] Connect the charger to the power supply.

[] Place the battery pack in the charger aligning raised rib on the battery pack with the groove in the charger.

See Figure 2.

APPLICATIONS

You may use this tool for the purposes listed below: [] Drilling in wood

[] Drilling in ceramics, plastics, fiberglass, and laminates

[] Drilling in metals

[] Mixing paint

CAUTION: If at any point during the charging process none of the LEDs are lit, remove the battery pack from the charger to avoid damaging the product. DO NOT insert another battery. Return the charger and battery to your nearest Sears or other qualified service center for service or replacement.

LED FUNCTIONS OF CHARGER

LED WILL BE ON TO INDICATE STATUS OF CHARGER AND BATTERY PACK:

[] Red LED on = Fast charging mode.

[] Green LED on = Fully charged and in maintenance charge mode.

[] Green LED on = When battery pack is inserted into charger, indicates hot battery pack or that battery pack is out of normal temperature range.

[] Yellow and Green LEDs on = Deeply discharged or defective battery pack.

[] No LED on = Defective charger or battery pack.

CHARGING THE BATTERY PACK

The battery pack for this tool has been shipped in a low charge condition to prevent possible problems. Therefore, you should charge it until the green LED on the front of the charger comes on.

NOTE: Batteries will not reach full charge the first time they are charged. Allow several cycles (operation followed by recharging) for them to become fully charged.

[] Press down on the battery pack to be sure contacts on the battery pack engage properly with contacts in the charger.

[] Normally the red LED on charger will come on. This indicates the charger is in fast charging mode.

[] Red LED should remain on for approximately 1 hour then the green LED will come on. Green LED on indicates battery pack is fully charged and charger is in maintenance charge mode.

NOTE: The green LED will remain on until the battery pack is removed from the charger or charger is disconnected from the power supply.

[] If both yellow and green LEDs come on, this indicates a deeply discharged or defective battery pack. Allow the battery pack to remain in the charger for 15 to 30 minutes. When the battery pack reaches normal voltage range, the red LED should come on. If the red LED does not come on after 30 minutes, this may indicate a defective battery pack and should be replaced.

[] After normal usage, a minimum of 1 hour of charging time is required to fully recharge battery pack.

[] The battery pack will become slightly warm to the touch while charging. This is normal and does not indicate a problem.

[] Do not place the charger and battery pack in an area of extreme heat or cold. They will work best at normal room temperature.

NOTE: The charger and battery pack should be placed in a location where the temperature is more than 50°F but less than 100°F.

[] When batteries become fully charged, unplug the charger from power supply and remove the battery pack.

10

Page 10
Image 10
Craftsman 315.115510 manual Charging a Cool Battery Pack, Applications, Charging the Battery Pack