CRRFTSMRN ®
OWNER'S MANUAL
Children operating or playing with s garage door
opener can injure themselves or others. The
garage door could close and cause serious injury or death.
Install the receiver (or any additional push buttons) out of the reach of children and away from all moving parts of the door and door hardware, but where the garage door is visible.
Do not allow children to operate the push button(s) or the remote control(s).
A moving garage door could injure someone under it. Activate the opener only when the door
is properly adjusted, you can see it clearly, and there are no obstructions to door travel•
DISCONNECT POWER TO THE GARAGE DOOR OPENER REFOREPROCEEDING.
The SECURITY+ Universal Remote Control Conversion Kit consistsof a receiver and remote control(s). This accessory will convert almost any garage door opener to rollingcode technology. The remote control sends a coded signal from outside the garage. Inside the garage, the
IMPORTANT: To improve the security of your opener, discard your old remote controls end erase or reset your code. For maximum security and range, you must disable the existing receiver on your opener, otherwise it could still activate your opener:
•If there is an external receiver, disconnect power to it.
•If it is an integrated receiver, either clip off the component that feeds power to the receiver or remove the tuning slug and antenna from the receiver section. If you have a different brand of opener, contact the manufacturer for additional information on disabling the existing receiver.
•If you have a Sears opener with an SRT receiver, erase the old codes by holding down the SRT button for 6 seconds until the indicator light turns off.
•If you have code switches, reset them to a random code and deactivate the receiver as follows: On the opener panel, peel
back the lower right _ | I_ I_ |
|
corner of the label to | Cut |
|
expose the tuning | Antenna | |
|
| |
slug (closest to the |
|
|
antenna), as shown. |
| Tuning |
Remove the slug | Slug | |
with a small hex | .Peal beck label | |
head wrench and cut | at | comet |
|
|
the antenna wire.
SECURITY,F
Universal Remote Control Conversion Kit
Model 139.53682 (With I Remote Control) Model 139.53683 (With 2 Remote Controls)
To complywith Fco rules,adjustmentsor modificationsof thr= reseivorand,/or transmitterare prohibited,except for changingthe code set_g o_ replacing
the ransmittorbattery.THERE ARE NO USER SERV CEABLE PARTS.
NOTICE TO U. S. CONSUMERS:
Some stat_s prohibitthe service or repairof garage door openers wbchcannotbe made to complywiththe safety standardscontained in UL 325 (1988 revision).In orderto complywith boththe letterand the spiritof these laws, this universalremote conttol converterkit shouldnot be used with any Sears Craftsman= garage door opener manufacturedpdorto Apdl1, 1982.
Power.. |
|
| !Terminals | |
Aotuator Cover Indicator | "o |
| Wire | |
| _11 | |||
SRT ._ |
|
|
| |
Indicator | Illico..act Bell Wire | |||
ght | ||||
Light | ||||
| L._ | to Garage Door | ||
I |
| |||
| Opener Terminals | |||
|
|
SRT (learn)
Antenna Actuator Belllwira
OPEN RECEIVER: Insert a small screwdriver in slot on receiver front panel as shown• Twist up actuator cover.
CONNECT RECEIVER AND OPENER: Remove about 1/4" of insulation from each end of the
(polarity is NOT required). Route wire along the channels and out the bottom as shown.
Connect the other end of the bell wire to the two opener
terminal screws labeled "2" (white) and "1" (red), "common" and "command" or the terminals used for the
push button control.
Use insulated staples (not supplied) to secure bell wire between receiver and opener. Length of bell wire depends on where the receiver will be installed. Replace the actuator cover.
Choose a 120Vac polarized outlet for the receiver which is OUT OF THE REACH OF CHILDREN. Plug receiver into selected outlet. Return power to the opener.