Replace the spark arresting screen if breaks occur.

Spark Exhaust

Arresting Outlet

Screen Cover

z

Nut

Muffler

CLEANING THE SPARK ARREST- ING SCREEN

Cleaning is required every 25 hours of

operation or annually, whichever comes first.

1.Loosen and remove the nut from the exhaust outlet cover.

2.Remove the exhaust oulet cover.

3.Remove spark arresting screen. Handle screen carefuIty to prevent damage.

4.Clean the spark arresting screen

gently with a wire brush. Replace screen if breaks are found.

5.Replace any broken or cracked muffler parts,

6.Reinstall spark arresting screen, ex- haust outlet cover, and nut. Tighten nut securely.

REPLACE SPARK PLUG

The spark plug should be replaced each year to ensure the engine starts easier and runs better. Ignition timing is fixed and nonadjustable.

,_b, WARNING: Disconnect the

spark plug before performing mainte- nance, service, or adjustments except for carburetor adjustments.

CHAIN SHARPENING

_I_WARNING: Improper chain

sharpening techniques and/or depth gauge maintenance will increase the chance of kickback which can result in serious injury.

_ WARNING: Wear protective

gloves when handling chain. The chain is sharp and can cut you even when it is

not moving.

Conditions which indicate the need for chain sharpening:

1.Loosen 3 screws on cylinder cover.

2.Remove the cylinder cover.

3.Pull offthe spark plug boot.

4.Remove spark plug from cylinder and discard.

5.Replace with Champion RCJ-7Y spark plug and tighten securely with a 3/4 inch (19 mm) socket wrench, Spark plug gap should be 0,025 inch (0,6 mm),

6, Reinstall the spark plug boot.

7, Reinstall the cylinder cover and 3 screws. Tighten securely,

Cy}inder

Cover

Spark

Plug Boot

Spark

Plug

REPLACE FUEL FILTER

To replace fuel filter, drain your unit by running it dry of fuel. Remove fuel cap and its connected retainer from tank.

Puit filter from tank and remove from line. Replace and reassemble.

•Reduction in size of wood chips, The size of the wood chip wilt decrease as the chain gets duller until it be- comes more like a powder than a chip. Note that dead or rotted wood will not produce a good chip.

•Saw cuts to one side or at an angle,

•Saw has to be forced through the cut.

Tool8 required:

•5/32 inch (4 mm) diameter round file and file holder

•Flat file

•Depth gauge tool

TO SHARPEN CHAIN:

1.Move ON/STOP switch to the STOP position.

2.Check chain for proper tension.

Adjust chain tension if necessary. See CHAIN TENSION section.

17

Page 16 Page 18
Page 17
Image 17
Craftsman 358.35161 manual Tool8 required
Page 16 Page 18

358.35161 specifications

The Craftsman 358.35161 is a reliable and powerful gas-powered string trimmer designed for homeowners and landscaping enthusiasts alike. Known for its robust performance, this trimmer offers a blend of innovation, comfort, and efficiency.

One of the standout features of the Craftsman 358.35161 is its 25cc 2-cycle engine. This engine provides ample power to tackle tough weeds, grasses, and overgrowth while delivering a user-friendly experience. The lightweight design of this trimmer, weighing approximately 10 pounds, also enhances its maneuverability, allowing users to navigate around gardens, flower beds, and landscaping projects with ease.

The Craftsman 358.35161 incorporates a straight shaft design, which is particularly advantageous for reaching under shrubs and in tight spaces. This design not only promotes better balance and control but also allows for greater reach, making it easier to access hard-to-reach areas. The 17-inch cutting swath ensures that users can cover a significant area in a single pass, improving efficiency during use.

Comfort is a priority with the Craftsman 358.35161, as evidenced by its cushioned grip handle and adjustable shaft length. These features combine to reduce operator fatigue during extended use, allowing users to work for longer periods without discomfort.

The trimmer is equipped with a dual line, bump-feed cutting system, which makes it easy to advance the line without stopping the engine. This system also allows for quick line replacement, enabling users to get back to work with minimal downtime. The 0.095-inch line thickness ensures effective cutting power while also being durable enough to withstand regular use.

A notable technological feature of the Craftsman 358.35161 is its Easy Start System, designed to simplify the starting process. This system reduces the amount of effort needed to start the engine, allowing for a smoother, quicker ignition every time. The fuel-efficient engine also contributes to fewer emissions, making it a more environmentally friendly choice compared to older models.

In summary, the Craftsman 358.35161 is an excellent choice for anyone looking for a versatile and efficient string trimmer. With its lightweight design, powerful engine, user-friendly features, and innovative technologies, it stands out as a reliable tool for maintaining beautiful landscapes. Whether you’re tackling simple yard maintenance or more demanding landscaping tasks, the Craftsman 358.35161 proves itself to be a valuable ally in your gardening endeavors.
Top Page Image Contents