TROUBLESHOOTINGCHART
PROBLEM | CAUSE |
|
| |||
Loss of power | 3. | |||||
continued) |
| and | trash under mower. | |||
| 4. | Dirty | air filter. |
| ||
| 5. | Low oil | leveVdirty oil. | |||
| 6. | Faulty | spark | plug. | ||
| 7. | Dirty fuel | filter. | |||
| 8. | Stale or | dirty | fuel. | ||
| 9. | Water | in fuel. |
| ||
| 10. Spark plug wire loose. | |||||
| 11. Dirty engine air screen/fins. | |||||
| 12. Dirty/clogged | muffler. |
t3. Loose or damaged wiring. 14.Carburetor out of
adjustment.
15.Engine valves out of adjustment.
Excessive | 1. | Worn, | bent |
| or loose blade. | ||||
vibration |
|
|
|
|
|
|
|
|
|
| 2. | Bent | blade |
| mandrel. | ||||
| 3. | Loose/damaged | part(s). | ||||||
Engine continues | 1. | Faulty | |||||||
to run when |
| presence | control | system. | |||||
operator leaves |
|
|
|
|
|
|
|
|
|
seat with |
|
|
|
|
|
|
|
|
|
attachment |
|
|
|
|
|
|
|
|
|
clutch engaged |
|
|
|
|
|
|
|
|
|
1. | Worn, | bent | or loose blade. | ||||||
| 2. | Mower | deck |
| not | level. | |||
| 3. | Buildup | of | grass, | leaves, | ||||
|
| and | trash | under | mower. | ||||
| 4. | Bent | blade |
| mandrel. | ||||
| 5. | Clogged | mower | deck vent | |||||
|
| from | |||||||
|
| leaves, | and | trash around | |||||
|
| mandrels. |
|
|
|
| |||
Mower blades will 1. Obstruction in clutch | |||||||||
not rotate |
| mechanism. |
|
|
| ||||
| 2. | Worn/damaged | mower | ||||||
|
| drive | belt, |
|
|
|
| ||
| 3. Frozen |
| idler | pulley. | |||||
| 4. | Frozen |
| blade | mandrel. |
CORRECTION
3.Clean underside of mower housing.
4.Clean/replace air filter.
5.Check oil level/change oil
6.Clean and regap or change spark plug.
7.Replace fuel filler.
8.Drain fuel tank and refill with fresh gasoline.
9.Drain fuel tank and carburetor, refill tank with
fresh gasoline and replace fuel filter.
lO.Connect and tighten spark plug wire.
11 .Clean engine air screen/ fins.
12.Clean/replace muffler.
13.Check all wiring.
14.See "To Adjust Carburetor" in Service Adjustments section.
15.Contact a Sears or other qualified service center.
1.Replace blade. Tighten blade bolt.
2.Replace blade mandrel.
3.Tighten loose part(s). Replace damaged parts.
1.Check wiring, switches and connections. If not corrected contact a Sears or other
qualified service center.
1.Replace blade. Tighten blade bolt.
2.Level mower deck.
3.Clean underside of mower housing.
4.Replace blade mandrel.
5.Clean around mandrels to open vent holes.
1.Remove obstruction.
2.Replace mower drive belt.
3.Replace idler pulley.
4.Replace blade mandrel.
31