RODUOT SPE¢ F CATUONS
MODEL | NUMBER | 917.377420 |
| |||
SERIAL | NUMBER |
|
|
| ||
DATE OF | PURCHASE |
|
|
| ||
HORSEPOWER: |
| 6.5 |
|
| ||
DISPLACEMENT: | 1256 | CUo IN. | ||||
GASOLINE | CAPACITY/TYPE: | Io25 | QtJARTS |
| ||
|
|
|
| UNLEADED | REGULAR | |
OIL TYPE | SAE | 30 (ABOVE 32°F) | ||||
|
|
|
| SAE | ||
OIL CAPACITY: |
| 20 OZS. |
| |||
SPARK | PLUG(GAP: °030") | CHAMPION | RJ19LM OR J19LM | |||
VALVE | CLEARANCE: | INTAKE: | ,,004" - °008" | |||
|
|
|
| EXHAUST: | °004" | |
SOLID | STATE | IGNITION |
|
|
| |
AIR GAP: |
|
| .0125 | IN. |
| |
BLADE | BOLT | TORQUE: | FT. LBSo | |||
•The model and serial numbers will be found on a decal attached to the rear of the lawn mower housing Record both serial number and date of purchase in space pro- vided above.
LAWN | MOWER |
|
|
|
|
| o Remove blade and attaching hardware | |||||||||||||||
|
|
|
|
|
|
|
|
|
|
| ||||||||||||
Always | observe | safety rules when perform- |
| (bolt, | lock washer | and hardened wash- | ||||||||||||||||
ing any | maintenance. |
|
|
|
|
| er),_ |
|
|
|
|
|
|
|
|
| ||||||
TIRES |
|
|
|
|
|
|
|
|
| NOTE: | Remove | the | blade | adapter | and | |||||||
• Keep tires free of gasoline, oil, or insect | check the key inside hub of blade adapter. | |||||||||||||||||||||
The key must be in good condition to work | ||||||||||||||||||||||
| control chemicals which can harm rubber. | |||||||||||||||||||||
| properly,. Replace adapter if damaged. | |||||||||||||||||||||
, Avoid stumps, stones, deep ruts, sharp | ||||||||||||||||||||||
|
|
|
|
|
|
|
|
|
|
| ||||||||||||
| objects | and | other | hazards that | may |
| TO REPLACE | BLADE |
|
|
|
| ||||||||||
| cause | tire | damage., |
|
|
| o | Position | the | blade | adapter | on the |
| |||||||||
BLADE | CARE |
|
|
|
|
|
| engine | crankshaft° | Be sure key in |
| |||||||||||
For best results, mower blade must be kept |
| adapter and keyway in crankshaft are | ||||||||||||||||||||
| aligned. |
|
|
|
|
|
|
|
| |||||||||||||
sharp_ Replace bent or damaged blades° |
|
|
|
|
|
|
|
|
| |||||||||||||
o Position blade on the blade adapter | ||||||||||||||||||||||
TO REMOVE |
| BLADE |
|
|
| |||||||||||||||||
|
|
|
|
| aligning the two (2) holes in the blade | |||||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
| |||||||||||
o | Disconnect | spark plug wire from spark |
| with | the | raised | lugs | on the adapter. | ||||||||||||||
| plug | and place | wire where it cannot | come | o | Be sure | the | trailing |
| edge | is up toward | |||||||||||
| in contact | with | spark | plug. |
|
|
| the engine_ |
|
|
|
|
|
|
| |||||||
o | Turn | lawn | mower | on | its side, | Make | sure | o install the blade bolt with | the | lock | wash- | |||||||||||
| air filter | and | carburetor | are up. |
|
| er and hardened washer | into blade | ||||||||||||||
o | Use a wood | block | between blade and |
| adapter | and | crankshaft, |
|
|
| ||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
| mower | housing | to | prevent blade from | o Use block of wood | between | blade | and | ||||||||||||||
| turning when removing blade bolt. |
|
| lawn | mower | housing | and | tighten | the | |||||||||||||
o Protect your hands with gloves and/or |
| blade bolt, turning | clockwiseo |
|
| |||||||||||||||||
| wrap | blade with heaw | cloth. |
|
| • | The | recommended |
| tightening | torque is | |||||||||||
o | Remove | blade | bolt by turning | counter- |
|
|
|
|
|
|
| |||||||||||
| clockwise. | Use | a 9/16" box or |
|
|
|
|
|
|
|
|
|
|
| ||||||||
wrench. | 11 |
|
