PRODUCT | SPECIFICATIONS |
|
|
|
|
| ||||
MODEL | NUMBER |
| 917.377542 |
|
| |||||
SERIAL | NUMBER |
|
|
|
|
| ||||
DATE OF PURCHASE |
|
|
|
|
| |||||
HORSEPOWER: |
|
| 6.5 |
|
|
| ||||
DISPLACEMENT: |
| 11.5 CU. IN. |
|
| ||||||
GASOLINE | CAPACITY/TYPE: |
| 1.6 QUARTS |
|
| |||||
|
|
|
|
|
| UNLEADED | REGULAR | |||
OIL TYPE |
| SAE 30 (ABOVE 32°1=) | ||||||||
|
|
|
|
|
| SAE | (BELOW | 32°F) | ||
OIL CAPACITY: |
|
| 20 OZS. |
|
| |||||
SPARK PLUG | (GAP: .030") |
| CHAMPION | RJ19LM | OR J19LM | |||||
VALVE | CLEARANCE: |
| INTAKE: | .004 | ||||||
|
|
|
|
|
| EXHAUST: | .004 | |||
SOLID | STATE IGNITION |
|
|
|
|
| ||||
AIR GAP: |
|
|
| .0125 | IN. |
|
| |||
BLADE | BOLT TORQUE: |
| FT. LBS. |
| ||||||
| The model and serial numbers will be found on a decal attached to the rear of the | |||||||||
| lawn mower housing,Record both serial number and date of purchase in space | |||||||||
| provided above. |
|
|
|
|
| ||||
LAWN | MOWER |
| • | Remove blade and attaching hardware | ||||||
|
|
|
|
| ||||||
Always observe safety rules when performing |
| (bolt, lock washer and hardened washer). | ||||||||
any maintenance. | NOTE: Remove the | blade adapter and | ||||||||
TIRES |
|
|
| check the key inside hub of blade adapter. | ||||||
• | Keep tires free of gasoline, oil, or insect | The key must be in good condition to work | ||||||||
| controlchemicals wh'_hcan harm rubber. | properly. Replace adapter if damaged. | ||||||||
• | Avok:lstumps, stones, deep ruts, sharp | |||||||||
TO REPLACE BLADE |
|
| ||||||||
| objects and other hazards that may cause |
|
| |||||||
| • | Positionthe blade adapter on the engine | ||||||||
| tire damage. |
| ||||||||
|
|
| crankshaft. Be sure key in adapter and | |||||||
BLADE CARE |
|
| ||||||||
|
| crankshaft keyway are aligned. | ||||||||
For best results, mower blade must be kept |
| |||||||||
• | Positionblade on the blade adapter aligning | |||||||||
sharp. Replace bent or damaged blades. | ||||||||||
| the two (2) holes in the blade with the raised | |||||||||
TO REMOVE BLADE |
| |||||||||
| lugson the adapter. |
|
| |||||||
• | Disconnect spark plug wire from spark plug |
|
|
| ||||||
• | Be sure the trailing edge of blade (opposite | |||||||||
| and place wire where it1_n_'t_me in |
| sharp edge) is up toward the engine. | |||||||
|
|
|
|
|
| |||||
| contact with spark plug. | • | Installthe blade belt with the lock washer | |||||||
• | Turn lawn mower on its side. Make sure air |
| and hardened washer into blade adapter | |||||||
| filterand carburetor are up. |
| ||||||||
|
| and crankshaft. |
|
| ||||||
• | Use a wood block between blade and | • | Use block of wood between blade and lawn |
mower housing to prevent blade from | mower housing and tighten the blade belt, | |
tuming when removing blade bolt. | ||
turningdockwise. | ||
|
•Protect your hands with gloves and/or wrap • The recommended tighteningtorque is 35-
blade with heavy cloth. | 40ft. bs. |
• Remove blade bolt by turning counter- | IMPORTANT: Blade belt is grade 8 heat |
clockwise. Use a 9/16" box or | treated. |
wrench. |
|