RULES FOR SAFE OPERATION (Continued)
•NEVER USE IN AN EXPLOSIVE ATMOSPHERE.
Normal sparking of the motor could ignite flam-
mable liquids, gases, or fumes.
•KEEP HANDLES DRY, CLEAN, AND FREE
FROM OIL AND GREASE. Always use a clean
cloth when cleaning. Never use brake fluids,
gasoline, petroleum-based products or any strong
solvents to clean your tool.
•STAY ALERT. Watch what you are doing and use
common sense. Do not operate tool when you are
tired. Do not rush.
•CHECK DAMAGED PARTS. Before further use of
the tool, a guard or other part that isdamaged
should be carefullychecked to determine that it will
operate properlyand perform its intended function.
Check for alignment of moving parts, binding of
moving parts, breakage ofparts, mounting, and
any other conditionsthat may affect its operation.
A guard or other part that is damaged should be
propedy repaired or replaced by an authorized
service center unless indicated elsewhere inthis
instructionmanual. =.
•DO NOT USE TOOL IF SWITCH DOES NOT
TURN IT ON AND OFF. Have defective switches
replaced by an authorized service center.
•DRUGS, ALCOHOL, MEDICATION. Do not
operate tool while under the influence of drugs,
alcohol, orany medication.
•DRILLING OR DRIVING SCREWS INTO
ELECTRICAL WIRING IN WALLS, CEILINGS,
OR OTHER AREAS CAN CAUSE THE BITOR
CHUCK TO BECOME ELECTRICALLY LIVE. Do
nottouch metal partswhen drillinginto a wall;
grasp only the insulated handle(s) or plastic
housing when usingthis tool. Make sure hidden
electrical wiring, water pipes, and mechanical
hazards are not in the path of the bit when drilling
into a wall.
•INSPECT FOR and remove all nails from lumber
before drilling.
IMPORTANT SAFETY RULES FOR BATTERYTOOLS
•Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
when not usingyour battery tool or when changing
accessories.
•USE ONLY THE CHARGER PROVIDED WITH
YOUR BATTERY TOOL. Do not substitute any
other charger. Use of another charger could cause
batteries to explode causing possible serious
injury.
DO NOT PLACE BATTERY TOOLS OR THEIR
BATTERIES NEAR FIRE OR HEAT. They may
explode.
•DO NOT CHARGE BATTERY TOOL IN A DAMP
OR WET LOCATION.
•Your battery tool should becharged in a location
where the temperature is more than 50°F but less
than 100°F.
•Under extreme usage ortemperature conditions,
battery leakage may occur. If liquid comes in
contact with your skin,wash immediately with
soap and water, then neutralize with lemon juice
orvinegar. If liquid gets inyour eyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attention.
•If carrying your battery tool atyour side, make sure
it is not running and your finger isnot onthe
switch.Avoid accidental starting.
•SECURE WORK before applying power. NEVER
hold workpiece in your hand oracross your legs.
•WHEN SERVICING USE ONLY IDENTICAL
CRAFTSMAN REPLACEMENT PARTS.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER
•SAVE THESE INSTRUCTIONS. This manual
contains important safety and operating
instructionsfor batterycharger item number
9-11065 (982033-001).
•Before using battery charger, read all instructions
and cautionary markings in this manual, on battery
charger, and productusing batterycharger.
AWARNING: To reduce risk ofinjury, charge only
nickel-cadmium type rechargeable batteries. Other
types of batteries mayburst causing personal
injuryand damage.
•Do not expose charger to rainor snow.
•Use of an attachment not recommended or sold by
the battery charger manufacturer may result in a
riskof fire, electricshock, or injury to persons.
•To reduce risk of damage to charger body and
cord, pull by charger body rather than cord when
disconnecting charger.
•Make sure cord is located so thatit will not be
stepped on, tripped over, or otherwise subjected to
damage or stress.