Crown CXM2000 warranty Rear Panel Connectors, USB Connector Connects for firmware update only

Rear Panel

CXM2000

Rear Panel Connectors

AC Power Inlet: Connects to 100V~120V or 220V~240V, 50Hz/60Hz AC power supply.

Power Voltage Switch: Select the power supply voltage to be 100V~120V or 220V~240V.

USB Connector: Connects for firmware update only.

8-way DIP Switches: Switches 1~4 are for JBL cinema speaker selection. Switch 5 is for fault detection. Switch 6 is for 5.1 or 7.1 channel instal- lation system selection. Switches 7 and 8 are for monitor and fault detection functions of subwoofer 1 and 2.

Output Connectors: Connects the HD-15 connec- tors to the Crown DSi series or XLC series ampli- fiers through VGA cables. This allows the CXM2000 to send and receive signals from the amplifiers for fault detection and monitor function.

L-Bi-amp:Connects to the amplifier of left channel (bi-amp speaker) or left and right channels (passive speaker).

R-Bi-amp:Connects to the amplifier of right chan- nel (bi-amp speaker).

C:Connects to the amplifier of center channel.

SW1: Connects to the amplifier of low frequency effect channel (subwoofer 1).

SW2: Connects to the amplifier of low frequency effect channel (subwoofer 2).

Ls/Rs: Connects to the amplifier of left surround & right surround channels.

Bsl/Bsr: Connects to the amplifier of back sur- round left & back surround right channels.

Input Connector: Connects the HD-25 connector to the main outputs of the cinema processor.

RS232 Connectors: Connects the RS232 con- nector to the Theater Management System (TMS) for sending fault detection results.

Power Consumption	100V ~120V / 220V ~ 240V, 50Hz / 60
	Hz, 50W
Processor Input Channels:	8 inputs (Left, Center, Right, Surround
	Left, Surround Right, Back Surround
	Left, Back Surround Right, Subwoofer).
Input Impedance	>10k Ω
(Processor Inputs)
Input Impedance (Power	>10k Ω
Amplifier Inputs)
Signal to Noise Ratio	104 dB (A weighted)
Crosstalk	> 80 dB (A weighted)
Internal Monitor Speaker	8W
Power
DSP Section	DSP only for Left, Right and Center
	channel speakers
Input EQ	High and low shelving filters
Output EQ	8 parametric filters per channel
Delay	Up to 10 msec total delay per channel
Presets	11 presets. One is “ bypass”. Ten are
	factory-set for JBL cinema systems.
Operating Temperature	32°F to 104°F (0°C to 40 °C) 95%
	relative humidity (non-condensing)
Dimension	18.97” X 8.26” X 3.46”
(L x D x H)	(482 mm X 210 mm X 88 mm)
Net Weight	10.47 lbs (4.75 Kg)
Net Shipping Weight	13.34 lbs (6.05 Kg)

The symbols shown above are internationally accepted symbols that warn of potential hazards with electrical products. The lightning flash with arrowpoint in an equilateral triangle means that there are dangerous volt- ages present within the unit. The exclamation point in an equilateral triangle indicates that it is necessary for the user to refer to the owner’s manual.

These symbols warn that there are no user serviceable parts inside the unit. Do not open the unit. Do not attempt to service the unit yourself. Refer all servicing to qualified personnel. Opening the chassis for any reason will void the manufacturer’s warranty. Do not get the unit wet. If liquid is spilled on the unit, shut it off immediately and take it to a dealer for service. Disconnect the unit during storms to prevent damage.

Crown’s Three-Year, No-Fault, Fully Transferable Warranty

Crown offers a Three-Year, No-Fault, Fully Transferable War- ranty for every new Crown amplifier—an unsurpassed indus- try standard. With this unprecedented No-Fault protection, your new Crown amplifier is warranted to meet or exceed original specifications for the first three years of ownership. During this time, if your amplifier fails, or does not perform to original specifications, it will be repaired or replaced at our expense. About the only things not covered by this warranty are those losses normally covered by insurance and those caused by intentional abuse. And the coverage is transferable, should you sell your amplifier. See your authorized Crown dealer for full warranty disclosure and details.

For customers outside of the USA, please contact your au- thorized Crown distributor for warranty information or call 574-294-8200.

Crown International 1718 W. Mishawaka Rd. Elkhart, IN 46517-9439 TEL: 574-294-8200 FAX: 574-294-8FAX www.crownaudio.com

Specifications subject to change without prior notice. Latest information available at www.crownaudio.com.

Crown and Crown Audio are registered trademarks of Crown International. Other trademarks are the property of their respective owners.

©2013 Crown Audio®, Inc. Printed in China

05/13