Manuals / Crown / Car Audio and Video / Car Amplifier

Crown XTI 2002, XTI 4002, XTI 6002, XTI 1002 Get Started, Stereo DSP Off, Factory Preset #2 Bridge

Models: XTI 1002 XTI 2002 XTI 4002 XTI 6002

1 52

Download 52 pages 49.71 Kb

Page 4

XTi2 Series Power Ampliﬁers

Get Started

Stereo DSP Off

This is the default mode the ampliﬁer is set to from the factory. The ampliﬁer is conﬁgured for stereo mode with all processing disabled.

1.Connect Left/Right signal source to Channel 1 and Channel 2 using the XLR connectors.

2.Connect a speaker to each channel output using Speakon®, Banana Plugs, or bare wire.

WARNING: Before you start to set up your ampliﬁer, make sure you read and observe the Important Safety Instructions found at the beginning of this manual.

XTi 6002 back panel shown.

See page 9 for XTi 1002, 2002 and 4002 back panel.

Factory Preset #2: BRIDGE

Putting the ampliﬁer in BRIDGE (bridge-mono) mode delivers the power of both amp channels into a single 8 or 4 ohm load. The XTi2 Series ampliﬁers

come pre-loaded with a preset that makes it easy to conﬁgure the ampliﬁer for this operation.

Before you get started ensure that you:

1. Connect signal source to Channel 1 and Channel 2 using XLR connectors (the ampliﬁer inputs will automatically be summed together when selecting this preset).

2.Connector the speaker as shown.

a.If using the binding post outputs, connect the positive terminal of the speaker to the positive terminal of Channel 1 and the negative terminal of the speaker to the positive terminal of Channel 2.

b.If using a Speakon® connector, connect the positive terminal of the speaker to 1+ and the negative terminal to 2+. Plug the connector into the Channel 1 output only.

Follow these quick steps to conﬁgure the ampliﬁer for BRIDGE operation:

1.Push the “Set/Enter” button and you will see the word “Preset” ﬂashing.

2.Push the “Set/Enter” button again to enter the list of presets in the ampliﬁer.

3.Push the “Next/Down” or “PREV/UP” button until the screen displays “Bridge”.

4.Push the “Set/Enter” button to conﬁrm your selection.

5.The display will now read “Bridge” with the Y icon and Bridge icon highlighted.

NOTE: Custom wiring should only be performed by qualiﬁed personnel.

page 4

Operation Manual

Image 4

Crown XTI 2002, XTI 4002, XTI 6002, XTI 1002 operation manual Get Started, Stereo DSP Off, Factory Preset #2 Bridge

Contents

XTi Some models may be exported under the name Amcron Important Safety Instructions XTi2 Series ampliﬁers require Class 2 output wiring Declaration of Conformity Get Started Factory Preset #2 BridgeStereo DSP Off Factory Preset #3 Xover Factory Preset #4 BRG Subs Factory Preset #5 Subsynth Get StartedEnsure Proper Cooling Before you get started ensure that you How to Use This Manual Next Generation Features includeWelcome Front Panel Features Indicators XTi 1002, 2002 Back Panel FeaturesXTi Menu Tree Front Panel NavigationNavigating the LCD Screen Menu Basics Integrated Processing Features Advanced Thermal Control Advanced MonitoringFront Panel Lock-Out /PSNBM &BSMZ VMM4QFFE XTi2 Serie Bedienungsanleitung Stereo DSP AUS InbetriebnahmeWerksvoreinstellung Nr Brücke Werksvoreinstellung Nr Xover Werksvoreinstellung Nr BRG Subs Inbetriebnahme Werksvoreinstellung Nr SubsynthStellen Sie eine korrekte Kühlung sicher Bevor Sie beginnen, stellen Sie sicher, dass Sie Die Features der nächsten Generation WillkommenVerwendung dieser Bedienungsanleitung Die Sie und die Welt bewegt Features der Vorderseite Features der Rückseite Navigation durch das Menü des LCD-Bildschirms Grundlagen Navigation auf der VorderseiteMenübaum Integrierte Verarbeitungsfunktionen EingangsmodusAusgangsmodus Equalizing Sperre der Tasten der Vorderseite /PSNBM 7PSFJUJH Údituesfibim Serie XTi2 Manual de Operación Algunos modelos pueden ser exportados bajo el nombre Amcron Cómo empezar Preajuste de fábrica núm Bridge Puente Preajuste de fábrica núm BRG Subs SUB-BAJOS Puenteados Preajuste de fábrica núm Xover Divisor DE Frecuencia Cómo empezar Compruebe que existe una ventilación correctaPreajuste de fábrica núm Subsynth Sintetizador subarmónico Antes de empezar, debe asegurarse de Las funciones de nueva generación son BienvenidoCómo usar el presente manual Funciones del panel frontal Funciones del panel posterior Navegación del panel frontal Menú de opciones Funciones de procesamiento integradas Limitador PeakX Plus Control térmico avanzadoControles avanzados Bloqueo del panel frontal Manuel d’utilisation de la série XTi2 Certains modèles peuvent être exportés sous le nom d’Amcron Commencez Stéréo DSP mode OffPréréglage usine #2 Bridge Préréglage usine #3 Xover Préréglage usine #4 BRG Subs Commencez Préréglage usine #5 SubsynthVériﬁer le fonctionnement du refroidissement Avant de commencer, assurez-vous Bienvenue Les caractéristiques nouvelle génération comprennentComment utiliser ce manuel PEQ pour une personnalisation du fonctionnement Caractéristique panneau avant Caractéristiques panneau arrière VentilateursPrises de sortie 4 pôles Speakon Connecteur USB HiQnet Menu Fonctionnalités panneau avantNaviguer dans le menu de lécran LCD Pour commencer Mode dentrée Mode de sortieCaractéristiques de traitement intégrées Égalisation Contrôle thermique perfectionné Commande perfectionnéeVerrouillage panneau avant XTi2 Specifications WeightDimensions. Width, Height, Depth behind mounting surface Performance Service Worldwide ServiceUS and Canada Service Service at a US or Canada Service Center Factory Service Packing Instructions Payment of Non-Warranty RepairsEstimate Approval Warranty United States & Canada Summary of Warranty Warranty Worldwide Except USA & Canada This page Intentionally Left Blank Crown Audio, Inc IT8000, CDi1000, PCC16 XTi2 Series Power Ampliﬁers Crown Audio Factory Service Information Type of credit card MasterCard Visa American ExpressCard # Exp. date *Card ID # Name on credit card Billing address of credit card