CTs Series 2-channel
uilding on the foundation of the Crown®
flexibility and value for installed sound appli- cations. The
All models in the CTs Series feature Crown’s new Switching Power Supply for lighter weight, and all models are also compatible with Harman Pro System Architect as well as the IQ System®.
In a profession where unplanned service calls quickly wipe out profits, the CTs Series amplifiers are designed to be the most reliable amplifiers you can install.
For more details about the Crown CTs Series, contact Crown Customer Service at
C T s S E R I E S
Features
• Switching Power Supply for reduced weight | • Comprehensive array of indicators including Power, | |
• High | Data and Bridge, along with Ready, Signal, Clip, | |
Thermal and Fault for each channel, provide accurate | ||
a 2U chassis | ||
diagnostics | ||
• Direct | ||
• Blue Power Indicator flashes if the AC mains is | ||
under/over voltage | ||
• Input sensitivity independently selectable for each | ||
• Advanced protection circuitry guards against: shorted | ||
channel | ||
outputs, DC, mismatched loads, general overheating, | ||
• TLC protection circuitry protects the amplifier from | ||
under/over voltage, | ||
internal faults | ||
reducing the gain only when necessary | • JTs circuitry (CTs 600/1200) quickly protects output | |
• PIP2 (Programmable Input Processor) connector | ||
transistors from unsafe operating conditions without | ||
accepts accessory modules that tailor the amplifier | shutting the channel down | |
to suit specific applications | • Legendary Crown AB+B | |
| ||
• Removable terminal block input connectors, with “Y” | topology in the CTs 600/1200 and Class I (BCA®) | |
Input Switch in the standard | output topology in the CTs 2000/3000 offer the best | |
• Switchable | in amplifier reliability | |
• Continuously variable fans optimize cooling efficiency | ||
former saturation when used in distributed systems | • Three Year, | |
| ||
| Warranty completely protects your investment and | |
| guarantees its specifications |
CTs 2000 | 20 | |
Power | ||
1000W | ||
1000W | ||
1000W | ||
625W | ||
70V Dual (per ch.) | 1000W | |
100V | Dual (per ch.) | 1000W |
2000W | ||
2000W | ||
2000W | ||
140V | Bridge | 2000W |
200V | Bridge | 2000W |
20
CTs 3000 | 20 | |
Power | ||
1500W | ||
1500W | ||
1250W | ||
625W | ||
70V Dual (per ch.) | 1500W | |
100V | Dual (per ch.) | 1500W |
3000W | ||
3000W | ||
2500W | ||
140V | Bridge | 3000W |
200V | Bridge | 3000W |
20
Specifications
Minimum Guaranteed Power: See power charts at left.
Frequency Response (at 1 watt, 20 Hz - 20 kHz): ±0.25 dB.
Signal to Noise Ratio below rated power (20 Hz to 20 kHz): 105 dB
Total Harmonic Distortion (THD) at full rated power, from 20 Hz to 20 kHz: CTs 600/1200: < 0.1%. CTs 2000/3000 < 0.35%.
Damping Factor: 10 Hz to 100 Hz: > 3000.
Crosstalk (below rated power, 20 Hz to 1 kHz): > 80 dB.
Common Mode Rejection (CMR) (20 Hz to 1 kHz): 50 dB.
DC Output Offset: < ±2 mV.
Input Impedance (nominal): 10 kilohms balanced, 5 kilohms unbalanced.
Maximum Input Level: +20 dBu before input com- pression, +32 dBu absolute maximum.
Load Impedance: (Note: Safe with all types of loads)
CTs 600/1200
Stereo: 2/4/8/16 ohms, 70V, 100V
Bridge Mono: 4/8/16 ohms, 140V.
CTs 2000/3000
Stereo: 2/4/8/16 ohms, 70V, 100V
Bridge Mono: 4/8/16 ohms, 140V, 200V.