Cub Cadet 19HP Enforcer 44, 21HP Enforcer 48, 23HP Enforcer 54 F.Related to Fuel, G.Towing

and is contained within the positive and negative ter-

minals as well as within the battery’s internal grid- work of plates and active materials.

A.Explosive gases are generated when batteries are re-charged, so sparks, flames and heat sources should be avoided. Loose connections at the battery terminals can produce sprks and heat...connections to the terminals must be kept tight, and the terminals and battery surfaces kept clean of acids and corro- sion. If batteries are re-charged or “jumped” from external sources, make sure that the connections are made properly and in the correct sequence...connect to the positive terminal of the good battery first, then connect that to the positive terminal of the weak bat- tery. The third connection should be to the negative terminal of the good battery, followed by the negative terminal of the weak battery. If sparks are observed or heating of the wiring or connectors is detected, disconnect in reverse order (I.E., the negative termi- nal of the weak battery first). Batteries should be re- charged at a constant voltage...generally 14.5 +/- 0.5 volts DC for a nominal 12 volt DC battery.

F.Related to Fuel

1.Fuel is highly flammable and its vapors can explode if ignited. Please respect it.

2.Do not smoke or permit others to smoke while handling fuel.

3.Always use approved containers for fuel and fill slowly to decrease the chance of static electricity buildup and spillage.

4.Store fuel in well ventilated and unoccupied buildings away from sparks and flames.

5.When dispensing gasoline into approved con- tainers, place the container on the ground when refueling to avoid a possible static elec- tricity ignition of fuel vapors.

6.Do not fill containers while it is inside a vehi- cle, trunk, the bed of a pickup or floor of a trailer.

7.Always shut off the engine and permit it to cool before removing the fuel tank cap.

8.Always fill the fuel tank outdoors.

9.If the fuel container spout will not fit inside the fuel tank opening, use a funnel.

10.When filling the fuel tank, stop when the fuel reaches one inch from the top. This space is necessary for tank expansion. Do not overfill.

11.Wipe up any spilled fuel.

attach towed equipment except at the hitch point.

2.Follow the manufacturers recommendation for weight limits for towed equipment and towing on slopes.

3.Never allow children or others in or on towed equipment.

4.On slopes, the weight of the towed equipment may cause loss of traction and loss of control. Note: 5 degrees (9%) maximum slope.

5.Travel slowly and allow extra distance to stop.

H.Suspension Seat

1.This unit is equipped with a heavy-duty vinyl fabric-covered seat incorporating adjustable armrests, an adjustable seatback, an adjust- able fore/aft track, a weight/ride adjustable mechanical suspension system, and an Operator Presence Sensor (OPS).

2.An OPS in the form of a switch, is integrated into the seat bottom and is connected to the machine electrical system. The weight/ride adjustment lever is located on the right side of the seatback and incorporates three set- tings: light = 110 lbs, medium = 195 lbs, and heavy = 286 lbs. Lever up is light and down is heavy. Weight adjustment should be made without the operator sitting in the seat. The seatback recline adjustment is also on the right side between the seat back and seat bottom, and it provides up to 10 degrees.

3.The fore/aft single-locking adjustment tracks operate on roller-bearings for smooth and almost effortless operation. The lever for seat track actuation is near the right front corner of the seat bottom, and allows fore/aft adjust- ment of 4”.

4.The seat is attached to pivotal brackets, which allow the seat assembly to pivot for- ward onto the foot platform area.

Note: The Operator Presence Sensor must be connected to the electrical wiring harness.

G.Towing

1.Tow only with a machine that has an approved hitch designed for towing. Do not

WARNING-YOUR RESPONSIBILITY: Restrict the use of this power machine to persons who read, understand and follow the warnings and instructions in this manual and on the machine.

7