cavitation to develop which can destroy the pumps in a short time.

Contaminants or foreign matter in the oil will also damage the pumps . To prevent this, use a filter that captures particles as small as 30 microns or 30 millionths of a meter in diame- ter. You can help in the battle against dirt by being very careful when you remove or repair a component in the hydraulic system. Thor- oughly clean off any component before you work on it. Plug the ends of any hose or line you remove with a rubber or plastic plug. Use plastic caps to seal off the ends of hydraulic fittings. Place any component you remove in a clean plastic bag so it can’t pick up dust or dirt. Clean your hands frequently when work- ing on the hydraulic components.

Note: The pumps are not owner-repairable. If a pump fails, contact your Cub Cadet Ser- vice Dealer. Do not disassemble the pump.

4.Steering Lever Adjustments: Place the mower on level ground with the engine run- ning, parking brake off and steering levers opened out to the neutral position. If the Mower begins to creep, adjust the Steering Levers.

If the mower creeps, first determine whether it creeps to the right or left side and which direc- tion the mower moves — to the front or the rear. To make the adjustment, place the steer- ing levers in the opened-out neutral position and set the parking brake, shutoff the engine, take the key from the ignition switch and pivot the seat forward. If the mower creeps to the right, you will adjust the linkage on the left side of the mower and vice-versa. Remove the cap screw and lock washer that secure the linkage control arm rod end bearing to the control lever pivot. Loosen the jam nut which prevents the rod end bearing from turning. If the mower creeps forward, thread the rod end bearing one-half turn clockwise into the link- age control arm. If the mower creeps back- ward, thread the rod end bearing one half turn counterclockwise out of the linkage control arm. Then tighten the jam nut and reconnect the rod end bearing to the control lever pivot by replacing the cap screw and lock washer.

After adjusting the steering linkage, swing the seat back to its normal position and place the steering lever on the side you adjusted up to the operating position. If you feel a slight push forward or a slight pull backward from the neutral position you must adjust the lever return assembly. To do this, swing the steering

lever back out to the neutral position, pivot the seat forward and loosen the jam nut on the lever return rod where it is threaded into the hex-shaped end of the lever return bolt. If the steering lever was pushed forward, turn the hex-shaped lever return bolt clockwise one- half turn off of the lever return rod. If the steer- ing lever was pulled back, turn the hex shaped lever return bolt counterclockwise one-half turn onto the lever return rod. Then tighten the jam nut, pivot the seat back into the operating position and start the mower to check that your adjustments were made correctly.

G.Storage

1.General: If your mower will not be in service for a few months, it should be stored in a dry location that is not subject to drastic changes in temperature. Before storing, the following maintenance procedures should be per- formed.

a.Clean the mower. The entire tractor and cutting deck should be washed and cleaned.

b.Sharpen the blades so that the mower will be ready to use when needed.

c.Protect the metal surfaces. Repair scratches with the appropriate touch-up spray paint. Brush a rust preventive oil on any unpainted surfaces including the pul- leys and blades. (Be careful not to get any oil on the drive belts.)

d.Lubricate the mower.

e.Drain the engine oil. The engine should be warm so that all the oil drains. Replace the engine oil filter and refill the crankcase with fresh oil.

f.Gasoline Engine: Drain all the fuel. Close the fuel tank shutoff valve. Disconnect the fuel line from the carbuetor and put the end into an approved fuel container. Open the fuel tank shutoff valve and drain the fuel tank and line into the approved container. Replace the fuel line on the carburetor. Start the engine and allow it to run out of fuel. This will prevent gum and varnish deposits from forming. Replace the fuel fil- ter.

g.Gasoline Engine Only: Remove the spark plugs and pour approximately one ounce of oil into each cylinder. Crank the engine one or two turns to spread the oil evenly on the cylinder walls. Replace the spark plugs.

h.Clean the battery and make sure it is fully charged.

21

Page 20 Page 22
Page 21
Image 21
Cub Cadet 23HP service manual Storage
Page 20 Page 22

23HP specifications

The Cub Cadet 23HP lawn tractor is a powerful and efficient machine designed for homeowners looking to maintain their lawns with ease. This lawn tractor offers a blend of performance, comfort, and innovation, making it a top choice for both small and medium-sized yards.

At the heart of the Cub Cadet 23HP is its reliable engine. The 23 horsepower engine provides ample power to tackle tough mowing conditions and hilly terrains effortlessly. The engine is designed for optimal performance, ensuring that the tractor operates smoothly under various conditions. With a reliable starter system, getting the tractor running is quick and efficient, allowing users to get to work without delay.

One of the standout features of the Cub Cadet 23HP is its innovative cutting deck. The 46-inch or 54-inch cutting deck options are designed for precision and efficiency, providing an excellent cut quality while reducing the time spent mowing. The deck is equipped with adjustable cutting heights, allowing users to customize their lawn care to match their specific needs. This adaptability ensures that the mower can handle different grass types and lengths with ease.

Comfort is another key characteristic of the Cub Cadet 23HP. The tractor features an adjustable high-back seat that provides support during long mowing sessions. Its ergonomic design ensures that users can maintain a natural posture while operating the tractor, reducing fatigue. The steering wheel is also designed for ease of use, allowing for smooth maneuverability even in tight spaces.

In terms of technology, the Cub Cadet 23HP comes equipped with advanced features that improve user experience. The LED headlights provide excellent visibility for early morning or late evening mowing. Additionally, the tractor features a dashboard with clear gauges that keep users informed about fuel levels, engine temperature, and other essential metrics.

Safety is a priority with the Cub Cadet 23HP. The tractor is equipped with safety features such as a seat switch that ensures the mower stops when the operator leaves the seat. This feature reduces the risk of accidents and enhances overall safety during operation.

Overall, the Cub Cadet 23HP lawn tractor combines power, comfort, and cutting-edge technology to deliver an exceptional mowing experience. Whether you have a small backyard or a larger property, this lawn tractor is designed to meet a variety of landscaping needs efficiently, making lawn care a hassle-free task. With its robust build and thoughtful features, the Cub Cadet 23HP is an investment in maintaining a beautiful lawn.
Top Page Image Contents