caps and drain oil from both left and right pumps. Replace and retighten nuts.

Hydraulic pumps

Figure. 9

Unfasten hose and drain from this side of both pumps.

j.Coat new filter seal with oil before installa- tion. Install new hydraulic oil filter filled with new oil.

k.Add proper amount of hydraulic oil to res- ervoir.

l.Run and purge gearboxes. Check oil level.

m.Add proper amount of hydraulic oil to res- ervoir and repeat step L.

C.Electrical Circuit

Danger:

Read General Safety Precautions Nos. 9 and 10.

1.Battery: The battery is located beneath the operator’s seat. Remove the fillcaps and check the level of the liquid electrolyte in the battery every 50 operating hours. If the level in any of the six cells has dropped below the bottom of the split ring inside the fill hole, refill the cell with distilled water. To keep the out- side of the battery clean, brush on a strong solution of bicarbonate of soda and water and rinse with clean water. Keep the contacts and cable ends clean with a wire brush and make sure the connections are tight. Coat the termi- nals with petroleum jelly to prevent corrosion.

2.Battery Storage: When storing the Mower for long periods of time the following guidelines should be taken.

a.Disconnect the battery cables from the ter- minals and remove the battery. You will have to remove the control panel to access the battery strap. Replace control panel.

b.Clean the battery before storing. A dirty battery will lose its charge over time.

c.Store the battery with a full charge. A dis- charged battery will freeze (refer to the table below).

Specific Gravity

Freezing Temp (°F)

 

 

1.265

-71

 

 

1.250

-62

 

 

1.200

-16

 

 

1.150

5

 

 

1.100

16

 

 

d.Recharge battery when ever the specific gravity value is less than 1.225

3.Battery Removal

Warning:

When removing the cables from the battery follow these steps to avoid a short between the wrench and the frame.

a.Remove the Negative (black) cable.

b.Remove the Positive (red) cable.

c.Release the hold down straps.

d.Remove the battery without tipping.

4.Installing the Battery

Note: The battery is delivered from the fac- tory fully charged and filled with electrolyte.

a.Attach the Positive (red) cable.

b.Attach the Negative (black) cable.

c.Attach the rubber battery strap.

5.Jump Starting

Warning:

Note: For E.F.I. Tanks, the battery must be disconnected (Negative lead) for storage exceeding four weeks. Do not “Jump Start” an E.F.I. unit, recharge or replace battery to avoid damage to the Electronic Control Unit (ECU).

Failure to use this starting procedure can cause sparking, and the gases in the battery to explode.

a.Attach the end of the red jumper cable to the Positive terminal (+) of the charged battery.

b.Attach the other end of the red jumper cable to the Positive terminal (+) of the low charge battery.

17

Page 16 Page 18
Page 17
Image 17
Cub Cadet 48-inch Fabricated Deck Electrical Circuit, Specific Gravity Freezing Temp F, Battery Removal, Jump Starting
Page 16 Page 18

48-inch Fabricated Deck specifications

The Cub Cadet 48-inch Fabricated Deck is a top-quality mowing solution designed for both residential and commercial users seeking durability and performance. This innovative mower deck stands out for its robust construction and versatile capabilities, providing an ideal balance for those who prioritize both efficiency and performance in their lawn care routine.

One of the standout features of the Cub Cadet 48-inch Fabricated Deck is its heavy-duty, 11-gauge steel construction. This not only enhances the deck's durability but also ensures that it can withstand the rigors of frequent use in various mowing conditions. The fabricated design contributes to a more solid and resilient structure compared to stamped decks, which often compromise performance over time.

Another key characteristic of this deck is its superior cutting performance. The 48-inch cutting width allows for efficient mowing in larger areas while enabling the user to navigate around obstacles with ease. The design incorporates precision-engineered blades, which facilitate a clean and uniform cut. The high-lift blades are particularly beneficial for discharging grass clippings effectively, ensuring a well-manicured appearance on any lawn.

The deck also features adjustable cutting heights, ranging anywhere from 1.5 inches to 4 inches, allowing users to customize their mowing experience based on the specific needs of their grass type and the current season. This adaptability ensures optimal results all year round.

Further enhancing the mowing experience, the Cub Cadet 48-inch Fabricated Deck integrates technologies that contribute to ease of use. The deck’s design allows for seamless attachment and detachment, making it easy to switch between mowing and other tasks. Additionally, the deck includes a maintenance-free spindle system, which reduces the need for regular upkeep and extends the overall life span of the mower.

The versatility of the deck also makes it compatible with several Cub Cadet riding mowers and lawn tractors, expanding its usability for a wide range of customers. Whether for tackling large yards or managing commercial properties, the Cub Cadet 48-inch Fabricated Deck proves to be an exceptional tool that combines strength, efficiency, and user-friendly features. Overall, this fabricated deck is an investment in quality lawn care, guaranteed to deliver outstanding performance and satisfaction for years to come.
Top Page Image Contents