f.Repeat as required to obtain proper throt- tle adjustment.

g.Verify proper throttle adjustment by check- ing RPM readings as outlined above.

C.Deck Corner Ball Wheel Roller Settings

1.Matching the set heights of the ball rollers on the four corners of the mower deck to the desired cut height will prevent edge scalping and minimize any side-to-side variance in cut height.

2.There are three height adjustment holes in the bracket that mount the ball rollers to the deck.

a.Use the top set of holes for cut heights of 2 inches or lower.

b.Use the middle set of holes for a 2-1/2 - 3-1/2 inch cut height.

c.Use the bottom set of holes for cut heights of 4 inches or higher.

D.Deck Center Anti-Scalp Roller Settings

1.The front and rear rollers help prevent the scalping of high spots and uneven terrain across the center section of the deck.

2.The rollers on the front of the deck are fixed at the factory and can not be adjusted.

3.The rollers on the rear of the deck can be adjusted downward one inch.

a.Lowering the roller will increase the strip- ing effect left behind the mower.

b.This positioning of the rear roller will also help to filter the mulched grass clippings into the turf.

c.Roller should not be lowered if the cut height is set at 2-1/2 inches or lower.

E.Lap Bar Adjustment

1.Proper lap bar and seat adjustment will result in the following:

a.In the neutral position with hands on the lap bars,

1.Operator’s upper arms should be relaxed and approximately vertical.

2.Operator’s forearms should be approxi- mately vertical.

b.In the full forward position,

1.Operator’s back should stay in contact with the seat back.

2.Lap bars should not contact operator’s legs.

c.In the full reverse position,

1.Lap bars should not contact the opera- tor’s legs or torso.

2.Set the seat to the preferred operating position.

a.Adjustment lever is located under the front edge of the seat.

b.The seat has five inches of front-to-rear adjustment available.

4.Check factory settings of lap bars for the con- ditions listed above.

Note: If lap bar adjustments are required,

height adjustments should be made prior to angular adjustments.

5.To adjust the height of the lap bars,

a.Remove the nuts from the lap bar mounting bolts (see Fig. 11).

b.Remove the bolts and lap bar and repostion to the seconc set of holes in the mounting block.

c.Replace the bolts and nuts and tighten to 28-34 ft-lbs.

1.If angular adjustments are also required, nuts can be tightened until snug at this point.

d.The same adjustments should be made to both sides of the mower.

6.To adjust the front-to-rear angle of the lap bars,

a.Loosen the nuts on the lap bar mounting bolts, leaving the bottom one fairly snug.

b.The top hole is slotted, allowing the lap bar to pivot on the bottom bolt.

c.Move lap bar to the desired angle and tighten the nuts to 28-34 ft-lbs.

Note: In the neutral position, the handles of

the lap bars should be aligned with approxi- mately a one inch gap between the tips. Adjus- the gap by adding shim washers to the top mounting bolt between the lap bar and the mounting block.

d.Check the results of any adjustments to the conditions described in section a, above. Repeat any adjustment procedures as required until all conditions are met.

Lap Bar Mounting Bolt and Nuts

Figure. 11

25

Page 24 Page 26
Page 25
Image 25
Cub Cadet 48-inch Fabricated Deck Deck Corner Ball Wheel Roller Settings, Deck Center Anti-Scalp Roller Settings
Page 24 Page 26

48-inch Fabricated Deck specifications

The Cub Cadet 48-inch Fabricated Deck is a top-quality mowing solution designed for both residential and commercial users seeking durability and performance. This innovative mower deck stands out for its robust construction and versatile capabilities, providing an ideal balance for those who prioritize both efficiency and performance in their lawn care routine.

One of the standout features of the Cub Cadet 48-inch Fabricated Deck is its heavy-duty, 11-gauge steel construction. This not only enhances the deck's durability but also ensures that it can withstand the rigors of frequent use in various mowing conditions. The fabricated design contributes to a more solid and resilient structure compared to stamped decks, which often compromise performance over time.

Another key characteristic of this deck is its superior cutting performance. The 48-inch cutting width allows for efficient mowing in larger areas while enabling the user to navigate around obstacles with ease. The design incorporates precision-engineered blades, which facilitate a clean and uniform cut. The high-lift blades are particularly beneficial for discharging grass clippings effectively, ensuring a well-manicured appearance on any lawn.

The deck also features adjustable cutting heights, ranging anywhere from 1.5 inches to 4 inches, allowing users to customize their mowing experience based on the specific needs of their grass type and the current season. This adaptability ensures optimal results all year round.

Further enhancing the mowing experience, the Cub Cadet 48-inch Fabricated Deck integrates technologies that contribute to ease of use. The deck’s design allows for seamless attachment and detachment, making it easy to switch between mowing and other tasks. Additionally, the deck includes a maintenance-free spindle system, which reduces the need for regular upkeep and extends the overall life span of the mower.

The versatility of the deck also makes it compatible with several Cub Cadet riding mowers and lawn tractors, expanding its usability for a wide range of customers. Whether for tackling large yards or managing commercial properties, the Cub Cadet 48-inch Fabricated Deck proves to be an exceptional tool that combines strength, efficiency, and user-friendly features. Overall, this fabricated deck is an investment in quality lawn care, guaranteed to deliver outstanding performance and satisfaction for years to come.
Top Page Image Contents