b.Avoid turning downhill if possible, if not use extra care and go slowly.

c.Avoid turning when going downhill, traction is at a minimum going downhill.

d.Do not operate with discharge side of the mower toward streets, buildings, play- grounds, parking lots, other machines, ani- mals, and other people.

e.Avoid operation or use extreme care if the traction surface is wet, unstable, or slip- pery.

f.Use extra care when grass clippings, leaves, pine needles, or debris are present as traction can be reduced.

g.Slow-down before turning and come to a complete stop before any zero turn maneu- ver.

h.Do not stop machine or park machine over combustible materials such as dry grass, leaves, debris, etc.

3.To Mow Grass and Produce a Striped Pat- tern

a.Pick a point on the opposite side of the area to be mowed (post, tree, shrub, etc.).

b.If on an hillside, start at the bottom so that the turns are uphill rather than downhill.

c.Align the mower so as to head directly toward the object on the far side.

d.Slowly increase the speed of the machine to match cutting conditions, terrain, and operator familiarity with the controls and keep the machine headed directly toward the alignment object. Do not go fast as to reduce cut quality or to be uncomfortable in controlling the speed and direction of the machine.

e.When approaching the other end of a strip, slow down or stop before turning. A U-turn is recommended unless a zero turn is required. The speed of a U-turn that will allow for machine controllability and mini- mal turf defacement will be dependent on several factors including: the speed of the turn, the radius of the turn, the tire tread pattern, the traction coefficient of the tire to the traction surface, the slope of the trac- tion surface.

f.Remember, a zero turn requires that the forward or reverse travel of the machine be stopped prior to the initiation of the turn or severe turf defacement can occur.

g.To prevent rutting or grooving of the turf, change the direction that the strips are mowed by approximately 45 degrees the next and each subsequent time that the area is mowed.

B.Controls

1.Engine Ignition and Start Switch: (See Fig- ure 1.) Located on the instrument housing below the right side of the operator’s seat. When the key is inserted and turned clock- wise, 45 degrees, the ignition circuit is closed. Turning the switch further against spring pres- sure starts the engine. The engine will only start if the blade clutch switch is in the “off” position, the parking brake is engaged and the left and right steering levers are in the neutral, opened-out position. The key should always be removed from the switch if the operator leaves the mower’s seat.

2.Engine Throttle Control: (See Figure 2.) Located on the left side of the mower next to the operator’s seat. Moving the throttle control from the rear to the front will increase the engine speed from slow to fast.

3.Left and Right Steering Levers: (See Figure 3.) These hinged levers open out to the side in the neutral position to permit the operator to be seated or to leave the mower’s seat. The operator, when seated, can pull the levers up to the operating position, a comfortable fore- arm’s length away. These levers control all of the movements of the mower. Pushing both levers forward causes the mower to move for- ward. Pulling both levers back causes the mower to move backward. Pushing one lever ahead of the other lever causes the traction wheel on the side where the lever is ahead to rotate faster than the other traction wheel, making the mower turn toward the side where the lever is behind. When one lever is pushed forward and the other lever pulled back the same amount, one traction wheel will turn in reverse and the mower will turn within its own length.

In order to start the engine, both steering levers must be opened out to the side in the neutral position; the parking brake must be engaged; and the blade clutch switch must be “off”. However, once the engine starts, the parking brake must be released before the operator places the steering levers into the operating position or the engine will automatically shut off.

Note: The Steering Lever will return toward neutral when released, but they should be placed in neutral by the driver. If the Drive Handles are not placed in neutral, the tractor may creep.

10

Page 9 Page 11
Page 10
Image 10
Cub Cadet 48-inch, 54-inch, 60-inch, 72-inch service manual To Mow Grass and Produce a Striped Pat- tern
Page 9 Page 11

48-inch, 54-inch, 60-inch, 72-inch, 54-inch, 72-inch specifications

Cub Cadet has long been a trusted name in outdoor power equipment, particularly when it comes to riding lawn mowers and lawn tractors. Among its impressive lineup, the 48-inch, 54-inch, 60-inch, and 72-inch cutting decks stand out for their power, performance, and innovative features tailored to meet the needs of both homeowners and professional landscapers.

Starting with the 48-inch cutting deck, this model is perfect for smaller to mid-sized lawns. It boasts a tight turning radius and exceptional maneuverability, making it easy to access narrow spaces and navigate around obstacles. Equipped with a powerful engine, the 48-inch deck provides efficient cutting, ensuring a professional finish every time.

The 54-inch cutting deck offers a slightly larger option, ideal for larger residential properties or commercial applications. This model incorporates advanced features such as the Cub Cadet’s AeroForce technology, which enhances airflow to create a superior cut and reduces clumping yard debris. The durable construction of the 54-inch deck ensures longevity, paired with easy-to-adjust cutting height settings for versatile lawn care.

For those requiring even more power and coverage, the 60-inch cutting deck delivers outstanding performance on expansive lawns. It features a heavy-duty design that enhances durability and precision in cutting. With exceptional stability, this mower easily handles uneven terrain, providing a consistent blade height thanks to its advanced deck leveling system.

The 72-inch cutting deck is designed for professional landscapers and those with substantial property needs. This deck covers wide areas rapidly, reducing mowing time. It is engineered with a robust build, featuring reinforced blades that enhance cutting power. The 72-inch model also incorporates vibration-dampening technology, ensuring operator comfort during extended use.

Across all Cub Cadet models, key characteristics include ease of use with an intuitive dashboard, hydrostatic transmission for smooth maneuvering, and powerful engines that cater to the rigors of lawn care. The mowers also boast innovative safety features, including automatic blade brake systems and operator presence controls that require the operator to remain engaged while mowing.

With exceptional cutting technology, robust engineering, and varied sizes to meet different lawn demands, the Cub Cadet 48-inch, 54-inch, 60-inch, and 72-inch cutting decks stand as top choices for anyone seeking reliability and performance in lawn care. Whether for residential use or professional landscaping, these mowers deliver quality results with each pass.
Top Page Image Contents