CyberPower Systems OR1500ELCDRM1U, OR1000ELCDRM1U Line mode, Battery mode, Trouble Shooting

	5. Replace the new battery pack. Assemble
4. Remove the retaining screw of	the screws, cover, cable and front panel in
	the reverse sequence of above steps.
the cable connectors.	Recharge the unit for 4-8 hours to ensure
	the UPS performs expected runtime

DEFINITIONS FOR ILLUMINATED LCD INDICATORS

Line mode

Select SW	UPS Status Display				Capacity		Digital Value Display
Press					Display
					Load	Battery	Input	Output	Run	% of	% of
					Cap.	Cap.	Voltage	Voltage	Time	Load	Batt.
Initial	V	X	--	X	V	X		V
1st	V	X	--	X	V	X			V
2nd	V	X	--	X	V	X				V
3rd	V	X	--	X	X	V					V
4th	V	X	--	X	V	X	V
5th(Return)	V	X	--	X	V	X		V
Press >3sec	V	X	V	X	--	--	--	--	--	--	--
(Sound
Disable)
Press >3sec	V	X	X	X	--	--	--	--	--	--	--
again(Sound
Enable)
(Overload)	V	X	--	V	--	--	--	--	--	--	--

"V" : Illuminated, "X" : Not Illuminated, "--" : Either

Battery mode

Select SW	UPS Status Display				Capacity		Digital Value Display
Press					Display
					Load	Battery	Input	Output	Run	% of	% of
					Cap.	Cap.	Voltage	Voltage	Time	Load	Batt.
Initial	X	V	--	X	V	X		V
1st	X	V	--	X	V	X			V
2nd	X	V	--	X	V	X				V
3rd	X	V	--	X	X	V					V
4th	X	V	--	X	V	X	V
5th(Return)	X	V	--	X	V	X		V
Press >3sec	X	V	V	X	--	--	--	--	--	--	--
(Sound
Disable)
Press >3sec	X	V	X	X	--	--	--	--	--	--	--
again(Sound
Enable)
(Overload)	X	V	--	V	--	--	--	--	--	--	--

"V" : Illuminated, "X" : Not Illuminated, "--" : Either

TROUBLE SHOOTING

Problem	Possible Cause	Solution
Full-time surge		Turn the UPS off and unplug at least one
protection outlets
	Circuit breaker has tripped	piece of equipment. Wait 10 seconds,
stop providing
	due to an overload.	reset the circuit breaker by depressing the
power to
		button, and then turn the UPS on.
equipment.
The UPS does	Battery not fully charged.	Recharge the battery by leaving the UPS
		plugged in.
not provide
expected
runtime.	Battery is slightly worn out.	Contact CyberPower Systems about
		replacement batteries at
		service@cyberpower-eu.com
	The on/off switch is	Turn the UPS off. Wait 10 seconds and
	designed to prevent
	damage by rapidly turning it	then turn the UPS on.
	off and on.
The UPS will not	The battery is worn out.	Contact CyberPower Systems about
turn on.		replacement batteries at
		service@cyberpower-eu.com
	Mechanical problem.	Contact CyberPower Systems at
		service@cyberpower-eu.com
	The USB cable is not	Connect the USB cable to the UPS unit
PowerPanel®		and an open USB port on the back of the
	connected.
Business Edition		computer.
	The unit is not providing	Shutdown your computer and turn the
is inactive.
		UPS off. Wait 10 seconds and turn the
	battery power.
		UPS on. This should reset the unit.

Additional troubleshooting information can be found at eu.cyberpowersystems.com

TECHNICAL SPECIFICATIONS

Model	OR1000ELCDRM1U		OR1500ELCDRM1U
Capacity (VA)	1000VA/600W		1500VA/900W
Input
Input Voltage Range	160VAC~270VAC
Frequency Range	50/60Hz (Auto Sensing)
AVR Function	Boost Only
Output
On Battery Output	230Vac +/-10%
Voltage
On Battery Output	50/60Hz +/-1%
Frequency
Transfer Time	4ms Typical
Overload Protection	On Utility: Circuit Breaker, On Battery: Internal Current Limiting
Surge Protection
Lightning / Surge		Yes
Protection
Network/ Phone/ Fax/	RJ11/RJ45 ( One In/ One Out )
Modem Protection
Operating Temperature	+32°F to 104°F ( 0°C to 40°C )
Physical
Total # of UPS outlets	IEC320 C 13 x 6 ( Backup x 4 )
Maximum	1U Rack 43.3 x 38.9 x 4.4		1U Rack 43.3 x 48.5 x 4.4
Dimensions(cm)
Weight (kg)	16.1		19.4
Battery
Sealed Maintenance	6V / 7Ah x4		6V / 9Ah x4
Free Lead Acid Battery
Typical Recharge Time		8 hours
Charging Current(Max.)		1A
User Replaceable		Yes
Status Indicators
Indicators	Power On, Wiring Fault, LCD Display
Audible Alarms	On Battery, Low Battery, Overload
Communication
PowerPanel® Business	Windows 2000/NT/XP/Vista,Mac OSX,Linux
Edition Software
Management
Self -Test		Yes
Auto-Charger		Yes
Auto-Restart		Yes
USB interface		Yes
Dry contact Closure		Yes
SNMP/HTTP		Optional
Networking

CYBERPOWER GREENPOWER UPS TECHNOLOGY

Our new UPS circuit is designed to save energy operating in GreenPower

Bypass Mode.

A traditional UPS circuit with AVR provides normal output voltage through the Relay and AVR transformer. The current travels first through the transformer conducting energy and generating heat. This heat creates energy dissipation resulting in a "Power Loss" or consumption of utility power and money.

CyberPower's GreenPower Circuit Design is a solution to this "Power Loss." When the Utility Power is operating normally, our Green Power UPS works in Bypass Mode. Our GreenPower design conducts power only through the Relay and still provides normal output voltage. Bypassing the transformer reduces power consumption thereby conserving energy and saving money. When the utility power is abnormal the UPS will operate under Battery or AVR Mode. Under this condition Green Power UPS and a traditional UPS would operate about the same.

On average utility power operates 88% of the time and the CyberPower GreenPower Technology will work in its money/energy saving Bypass Mode.

For more information, visit eu.cyberpowersystems.com or contact

CyberPower Systems B.V.

Flight Forum 3545 5657DW Eindhoven The Netherlands

Tel: +31 40 2348170, E-MAIL: sales@cyberpower-eu.com

CyberPower Systems Inc. (USA) 4241 12th Avenue East, Suite 400, Shakopee, MN 55379, U.S.A. Tel: +1 952 4039500, Fax: +1 952 4030009, E-MAIL: sales@cyberpowersystems.com

Entire contents copyright ©2004 CyberPower Systems B.V., All rights reserved. Reproduction in whole or in part without permission is prohibited. PowerPanel® and PowerPanel® Plus are trademarks of CyberPower Systems (USA) Inc.