Unpacking

eu.cyberpowersystems.com

Utility Tower Series UPS

UP350TE/UP500TE/UP500E/UP750E

User Manual

K01-U350E0A-01

SAFETY WARNINGS

(SAVE THESE INSTRUCTIONS)

This manual contains important safety instructions. Please read and follow all instructions carefully during installation and operation of the unit. Read this manual thoroughly before attempting to unpack, install, or operate your UPS.

This equipment can be operated by any individuals with no previous training.

The socket-outlet shall be installed near the equipment and easily accessible.

During the installation of this equipment it should be assured that the sum of the leakage currents of the UPS and the connected loads does not exceed 3.5mA.

Attention, hazardous through electric shock. Also with disconnection of this unit from the mains, hazardous voltage still may be accessible through supply from battery. The battery supply should be therefore disconnected in the plus and minus pole at the quick connectors of the battery when maintenance or service work inside the UPS is necessary.

Do not dispose of batteries in a fire, the battery may explode.

Do not open or mutilate the battery or batteries, released electrolyte is harmful to the skin and eyes.

INSTALLING YOUR UPS SYSTEM

Inspect the UPS upon receipt. The box should contain the following:

UPS Unit; PowerPanel® Software Disk¯1; Serial Interface Cable (DB-9)¯1; Telephone Cable¯1; IEC-IEC Power Cord¯2; User Manual; PowerPanel® Software User Manual.

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

1.Insure that the equipment plugged into the battery power-supplied outlets does not exceed the UPS unit’s rated capacity (350VA/210W for UP350TE, 500VA/300W for UP500TE, 500VA/325W for UP500E, 750VA/450W for UP750E). If rated unit capacities are exceeded, an overload condition may occur and cause the UPS unit to shut down or the circuit breaker to trip.

2.If the power requirements of your equipment are listed in units other than Volt-Amps (VA), convert Watts (W) or Amps (A) into VA by doing the calculations below. Note: The below equation only calculates the maximum amount of VA that the equipment can use, not what is typically used by the equipment at any one time. Users should expect usage requirements to be approximately 60% of below value.

TO ESTIMATE POWER REQUIREMENTS

Watts (W) x 2.0 =

VA or

Amps (A) x 230 =

2.Add the totals up for all pieces of equipment and multiply this total by 0.6 to calculate actual requirements. There are many factors that can affect the amount of power that your computer system will require. The total load that you will be placing on the battery-powered outlets should not exceed 80% of the unit’s capacity.

HARDWARE INSTALLATION GUIDE

1.Connect the equipment to your UPS outlets. The IEC-IEC power cords coming with the unit are used to connect your computer and monitor to the UPS. Items such as copiers, laser printers, vacuums, space heaters, or other large electrical devices should not be connected to the UPS. Please make sure that the total loads of your equipments are less than the maximum total power load of your UPS.

2.Use your computer power cord to connect the UPS to a wall outlet. Please avoid using extension cords and adapter plugs. (To maintain optimal battery charge, leave the UPS plugged in at all times.)

3.Press the UPS power button to turn it on. The “Power On” indicator will be illuminated in “Green”.

4.Install your software and accessories. To use the software, simply connect the enclosed serial interface cable to the serial port on the UPS and an open serial port on the computer.

BASIC OPERATION

FRONT PANEL AND REAR PANEL DESCRIPTION

POWER	USING
ON	BATTERY

POWER	USING
ON	BATTERY

UP350TE/UP500TEUP500E/UP750E

◆Power Switch

Press the power button to turn the UPS ON or OFF.

◆Power On Indicator

This LED is illuminated when the utility condition is normal and the UPS outlets are providing “clean power”, free of surges and spikes.

◆Using Battery Indicator

This illuminates during utility failure, indicating that the battery is supplying power to the battery-power supplied outlets.

◆Battery Backup and Surge Protection Outlets

The UPS provides battery powered and surge protected outlets for connected equipment to insure temporary uninterrupted operation during a power failure and against surges and spikes.

◆Surge Protection Outlets

The UPS provides surge protected only outlet for connected equipments against surges and spikes.

◆Serial Port to PC

This port allows connection and communication from the DB-9 serial on the computer to the UPS unit. The UPS communicates its status to the PowerPanel® software. This interface is also compatible with the UPS service provided by Windows 98, Windows

ME, Windows NT, Windows 2000, Windows XP, Windows Server 2003.

◆Ethernet (RJ-45) Network Protection Ports

These ports are the protection for your computer network cable.

BATTERY REPLACEMENT AND STORAGE

CAUTION! Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the battery.

Service the battery under the supervision of personnel knowledgeable of batteries and their precautions. Keep unauthorized personnel away from batteries. If you have questions, contact your dealer or call the number in this manual for information on battery replacement.

CAUTION! Use only the specified type of battery. See your dealer for replacement batteries. CAUTION! The battery may present the risk of electrical shock. Do not dispose of batteries in a fire, as it may explode. Follow all local ordinances regarding proper disposal of batteries. CAUTION! Do not open or mutilate the batteries. Release electrolyte is harmful to the skin and eyes and may be toxic.

CAUTION! A battery can present a high risk of short circuit current and electrical shock. Take the following precautions before replacing the battery:

1. Remove all watches, rings or other metal objects.

2. Only use tools with insulated handles.

3. DO NOT lay tools or other metal parts on top of battery or any battery terminals.

4. Determine if the battery is inadvertently grounded. If inadvertently grounded, remove source of ground. CONTACT WITH A GROUNDED BATTERY CAN RESULT IN ELECTRICAL SHOCK! The likelihood of such shock will be reduced if such grounds are removed during installation and maintenance (applicable to a UPS and a remote battery supply not having a grounded circuit).

5. Batteries are consider HAZARDOUS WASTE and must be disposed of properly. Contact your local government for more information about proper disposal and recycling of batteries.

6. Turn off and unplug all connected equipment.

7. Turn the UPS off and unplug it from the AC power source.

8. Turn the UPS upside down.

UP750E, UP500TE, UP500E, UP350TE specifications

CyberPower Systems is a well-known brand in the uninterruptible power supply (UPS) market, offering a robust selection designed to protect electronic devices from power outages and fluctuations. The UP750E, UP350TE, UP500E, and UP500TE are four notable models that cater to different needs and applications, ensuring consistent power availability and safeguarding sensitive equipment.

The UP750E is a versatile UPS designed to deliver reliable backup power. It features a capacity of 750 VA / 450 Watts, making it ideal for home office setups, networking equipment, and gaming consoles. One of its main features is the Automatic Voltage Regulation (AVR), which stabilizes output voltage and protects devices from fluctuations. Additionally, it includes multiple outlets, providing convenience for connecting multiple devices without compromising performance. The compact design allows for easy placement in various environments, whether under a desk or on a shelf.

Moving to the UP350TE, this model is designed for smaller systems with a capacity of 350 VA / 210 Watts. This unit is suitable for protecting low-power electronics like routers, modems, and personal computers. It incorporates features such as the energy-saving GreenPower UPS technology, which enhances efficiency and extends battery life. The UP350TE is appreciated for its user-friendly interface, with indicators that display battery status and load capacity, ensuring users remain informed about the backup status.

The UP500E provides a balanced solution with a capacity of 500 VA / 300 Watts, making it a solid choice for various electronic devices. It includes an LCD display that provides real-time information on battery status, load levels, and estimated runtime. This feature allows users to monitor the UPS at a glance. Similar to the other models, it employs AVR technology, ensuring that connected devices receive stable power, free from surges or sags.

Lastly, the UP500TE enhances the functionality of UPS systems with additional features suitable for more demanding applications. With a 500 VA / 300 Watts capacity, it includes USB connectivity, allowing for seamless integration with computers for automatic shutdown and power management. The model also utilizes battery optimization technology, which prolongs battery lifespan, ensuring that users can rely on the UPS for long-term protection.

In summary, CyberPower Systems offers the UP750E, UP350TE, UP500E, and UP500TE as a comprehensive suite of UPS solutions designed to meet various power protection needs. Each model is equipped with essential features such as AVR, energy-efficient technologies, and user-friendly interfaces, making them suitable for a wide range of applications, from personal use to professional environments. With these UPS systems, users can enjoy peace of mind, knowing that their electronic investments are well-protected from power interruptions and fluctuations.

CyberPower Systems UP350TE, UP750E, UP500E user manual Unpacking, To Estimate Power Requirements

Models: UP750E UP500TE UP500E UP350TE