Manuals / Dell / Computer Equipment / Computer Drive

Dell CX193 manual Guide de mise en route

Models: CX193

1 80

Download 80 pages 58.11 Kb

Specifications Install Connecting the Power Instalação e configuração System Features

Page 38

36

Guide de mise en route

Page 37 Page 39

Image 38

Dell CX193 manual Guide de mise en route

Page 37 Page 39

Related pages Troubleshooting for HP 420 Optional Accessories & Specifications for Monessen Hearth GPF36 Indicator lights for Miele KM 6207 A. Appliance Dimension Diagram for Heatiator GB4336 When you are finished editing contact for Motorola 6887460Z69 Caract ristiques Installation for Crest Audio LQ 10P Parts list for Zenoah G3200EZ Country/Area Code List for Toshiba SD-V65HTSU the torque arm of the dynamometer to insure that there is no force being applied to the load cell which would result in an inaccurate zero calibration. Remove the calibration access cover panel and set the calibration mode switch to the ZERO position. Also, be sure that the shunt resistor switch is set to the OFF position. At this time note that the RPM display of the unit should indicate “1111” and the POWER display should indicate “0000”. The TORQUE display indicates the TORQUE and should read near zero. If the torque indication is excessive plus or minus, the POWER display will read “EEEE” - which indicates that the zero offset of the load cell is excessive and that the ZERO calibration cannot proceed see calibration notes below. Otherwise, press and release the ENTER push-button switch to perform the zero calibration. At this point, the TORQUE display should indicate zero and the zero calibration procedure has been completed for Powerware ST-2400S How do I move multiple messages at once? Read the guide

Contents

Getting Started With Your System Page Getting Started With Your System September CX193 Contents Contents System Features Getting Started With Your System Obtaining Technical Assistance Supported Operating SystemsOther Information You May Need Installation and Configuration Unpacking the System Installing the Rails and System in a Rack Connecting the Keyboard, Mouse, and Monitor Connecting the Power Installing the Power Cord Retention Bracket Turning on the System Installing the Bezel Complete the 0perating System SetupTechnical Specifications Install the bezel optional One optional CD, DVD, or combination Sata Video Pin VGA Weight maximum 49.9 kg 110 lb Configuration Environmental Getting Started With Your System Index Index Guide de mise en route Remarques, avis et précautions Sommaire Sommaire Caractéristiques du système Un minimum de 512 Mo sous forme de barrettes Dimm FBD Six connecteurs USB 2.0 deux à lavant et quatre à larrière Systèmes dexploitation pris en charge Autres informations utiles Guide de mise en route Déballage du système Installation des rails et du système dans un rack Connectez le clavier, la souris et le moniteur facultatif Connexion du clavier, de la souris et du moniteurBranchement des câbles dalimentation Fixation du support du câble dalimentation Mise sous tension du système Installez le cadre facultatif Finalisation de linstallation du système dexploitationInstallation du cadre Spécifications techniques De 3,5 pouces, enfichables à chaud Un lecteur de CD ou de DVD, ou un lecteur CD-RW/DVD tous deux en option Toute la gamme ambiante de fonctionnement Page Guide de mise en route Contrôleur d’accès à distance gestion de systèmes à distance Index Primeiros passos com o sistema Notas, Avisos e Advertências Índice Índice Recursos do sistema Memória mínima de 512 MB com Fully Buffered DIMMs FBD Uma unidade opcional de CD, DVD ou combinação de CD-RW/DVD Nota Os dispositivos de DVD destinam-se somente a dados Sistemas operacionais compatíveis Outras informações úteis Como obter assistência técnica Instalação e configuração Remoção do sistema da embalagem Instalação dos trilhos e do sistema no rack Conexão de teclado, mouse e monitor Conecte o teclado, o mouse e o monitor opcional Conexão da energia Conecte os cabos de alimentação ao sistema Instalação do suporte de retenção do cabo de alimentação Instale a tampa frontal opcional Como ligar o sistemaInstalação da tampa frontal Conclua a configuração do sistema operacional Especificações técnicas Combinação de CD-RW/DVD Unidade de disquete Energia Ambientais Índice remissivo Índice remissivo Procedimientos iniciales con el sistema Notas, avisos y precauciones Contenido Contenido Componentes del sistema De memoria idénticosPage Sistemas operativos admitidos Otra información útil Instalación y configuración Obtención de asistencia técnica Desembalaje del sistema Instalación de los rieles y del sistema en un rack Conexión del teclado, el ratón y el monitor Conecte el teclado, el ratón y el monitor opcional Conexión de la alimentación Conecte los cables de alimentación al sistemaPage Encienda el sistema y el monitor opcional Encendido del sistemaInstalación del embellecedor Instale el embellecedor opcional Especificaciones técnicas Finalización de la instalación del sistema operativo Combinada de CD-RW/DVD Litio-ion de 4,1 Las orientaciones Índice Índice

Top Page Image Contents