1.Accendere la macchina.
2.Press the MENU button to enter the settings menu. Press the 
or 
button until “Descale” is displayed;
3.Press the OK button.“Descale Confirm?”is displayed. Press OK to enable the function.
4.The message “Add descaler Press OK” is displayed.
5.Before confirming, empty the water tank (A13).
Pour the descaler diluted with water (respecting the proportions indicated on the descaler pack) into the water tank and replace the tank in the appliance.
6.Place an empty container with a minimum capacity of 1.5 litres under the hot water spout.
Important! Danger of burns
Hot water containing acid flows out of the hot water spout. Avoid contact with splashes of water.
7.Confirm with the OK button.
8.“TURN STEAM KNOB” is displayed.
9.After turning the knob to the I position (fig. 4), “Descale
Press OK” is displayed.
10.After confirming by pressing OK, the message “Descale underway” is displayed.
The descale programme starts and the descaler liquid comes out of the water spout.
The descale programme automatically performs a series of rinses and pauses to remove limescale deposits from
inside the machine.
After about 30 minutes, “TURN STEAM KNOB” is displayed. When the steam knob is turned to the 0 position, “Rinsing FILL TANK” is displayed.
11.The appliance is now ready for rinsing through with clean water. Remove the water tank, empty, rinse under running water, fill with clean water and replace. “TURN
STEAM KNOB” is displayed. When the steam knob is turned to the I position, “Rinsing... Press OK” is displayed.
12.Empty the container used to collect the descaler solution and replace it under the hot water spout.
13.Press the OK button to start rinsing. Hot water flows out of the spout and the message “Rinsing... Please wait” is displayed.
14.When the water tank is completely empty, “TURN STEAM
KNOB” is displayed.
15.When the steam knob is turned to the 0 position, the
appliance goes off.
To use it again, turn the appliance on by pressing the button.
SETTING WATER HARDNESS
The DESCALE message is displayed after a period of time established according to water hardness.
The machine is set by default for a hardness value of 4 (very hard water).
The machine can also be programmed according to the actual hardness of the mains water in the various regions, varying the frequency with which the message is displayed.
Measuring water hardness
1.Remove the “TOTAL HARDNESS TEST” indicator paper from its pack.
2.Immerse the paper completely in a glass of water for one second.
3.Remove the paper from the water and shake lightly. After about a minute, 1, 2, 3, or 4 red squares form, depending on the hardness of the water. Each square corresponds to one level.
Level 1 - soft water •
Level 2 - slightly hard water
••
Level 3 - hard water
•••
Level 4 - very hard water
••••
Set water hardness
1.Press the MENU button to enter the settings menu.
2.Press the 
or 
button and select “Water hardness”.
3.Confirm the selection by pressing theOK button.
4.Press the 
or 
button to set the water hardness identified using the indicator paper (see figure in the previous section).
5.Press the OK button to confirm the setting.
6.Press the ESC button to exit the menu.
The machine is now reprogrammed with the new water hardness setting.
TECHNICAL SPECIFICATION
Voltage: | ||
Absorbed power: |
| 1350W |
Pressure: |
| 15 bar |
Water tank capacity: |
| 1,7 l |
Size: LxHxD: |
| 282x374x441 mm |
Cable length: |
| 1,5 m |
Weight: |
| 11,4 Kg |
Max. beans container capacity | 250 g | |
16
