DeLonghi DEDW87S Full 3/4 Full 1/2 Full 1/4 Full, Empty, Control Panel, Turning Onthe Appliance

Half Load Button: To select Half load functions. (Half load function means that the lower spray arm does not run, so you should load the upper basket only).

Using Your Dishwasher

Using Your Dishwasher

CONTROL PANEL

1 2 4 5 6 7 8

BEFORE STARTINGTHE DISHWASHER

The following things should be checked before starting the dishwasher.

As the rinse aid diminishes, the size of the black dot on the rinse aid level indicator changes, as illustrated below.

AUTO					1	PROG.
					2
	Heavy			Rapid
AUTO Intensive		Normal	Rinse		Soak

1.	That the dishwasher is level and fixed properly.
2.	That the inlet valve is open .
3.	That there is no leakage at the connections of the
	conducts.
4.	The wires are tightly connected and the power is
	switched on.

Full

3/4 Full

1/2 Full 1/4 Full

(Should refill to eliminate spotting)

C (Rinse-Aid indicator)

MIN

3

5.	That the inlet and drain hoses are not knotted or
	kinked.
6.	All packing materials should be taken out of the
	dishwasher.

Empty

1Power switch: To turn on/off the power supply.

2Power indicator light: Becomes lit when the ON/OFF button is pressed down.

3Display window: Program remaining time, delay time, running indicator, fault codes etc.

4Half Load light: Indicates a Half load wash.

5

6	Delayed Start Button: Press this button to set
	the delayed hours for washing. You can delay
	the start of washing up to 24 hours. One press
	on this button delays the start of washing by half
	an hour.
7	Display window: Delay time and fault codes
	and P1 to P7 will be displayed here, P1 to P7
	correspond to the 7 programs.
8	Program Button: Press this button to select the

PRIORTO USING FORTHE FIRSTTIME

Before using your dishwasher for the first time:

Fill the Rinse Aid Dispenser

The rinse aid is released during the final rinse to prevent water from forming droplets on your dishes, which can leave spots and streaks. It also improves drying by allowing water to roll off the dishes. Your dishwasher is designed to use liquid rinse aids. The

How to fill the Rinse Aid Dispenser

1.To open the dispenser, turn the cap to the "open" (left) arrow and lift it out.

2.Pour the rinse aid into the dispenser, being careful not to overfill.

3.Replace the cap by inserting it aligned with "open" arrow and turning it to the closed (right) arrow.

desired washing program.

rinse aid dispenser is located inside the door next to the detergent dispenser. To fill the dispenser, open the cap and pour the rinse aid into the dispenser until the level indicator turns completely black. The volume of

1

TURNING ONTHE APPLIANCE

Starting a wash cycle:

1.	Draw out the lower and upper basket, load the
	dishes and push them back. It is recommended to
	load the lower basket first, then the upper one (see
	the section entitled “Loading the Dishwasher”).
2.	Pour in the detergent (see Page 10).
3.	Insert the plug into the socket. The power supply is
	220-240 VAC /50 HZ, the specification of the
	socket is 10A 250VAC. Make sure that the water
	supply is turned on to full pressure.
4.	Open the door, press the ON/OFF button, and the
	ON/OFF light will turn on.

CHANGETHE PROGRAM

Premise:

1.A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the detergent may have already been released, and the appliance may have already drained the wash water.

If this is the case, the detergent dispenser must be refilled (see the section entitled "Adding Detergent").

2. Open the door, press the PROG. button more than

three seconds to cancel the program, then you can

change the program to the desired cycle setting.

Then, close the door.

the rinse aid container is about 140ml.

Function of the Rinse Aid

Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and streak free drying.

WARNING!

Only use branded rinse aid for dishwasher. Never fill the rinse aid dispenser with any other substances (e.g. Dishwasher cleaning agent, liquid detergent). This would damage the appliance.

When to refill the Rinse Aid Dispenser

3

5. Press the program button to select your desired

wash cycle, then close the door, the dishwasher

will start after 10 seconds.

The display window shows the state of the dishwasher:

a)LED shows '-:--' -- Stand by

b)LED shows 'H:MM' and not blinking--Being paused

c)LED shows 'H:MM' and blinking--Running

NOTE:

If you open the door during a wash cycle, the machine will pause. The LED Display Window will stop blinking and the buzzer will sound every minute unless you close the door. After you close the door, the dishwasher will continue working after 10 seconds.

If display window shows error codes after a warning sound (see page 21 for “ERROR CODES"), that indicates the machine is out of order, please turn off the main power and water supply before calling for service.

If there is no rinse-aid warning light in the control panel, you can judge the amount of rinse-aid by the color of the optical level indicator "C” located next to the cap. When the rinse-aid container is full, the whole indicator will be dark. As the rinse-aid diminishes, the size of the dark dot decreases. You should never let the rinse aid get below 1/4 full.

Be careful not to overfill the dispenser, because this could cause over sudsing. Wipe away any spills with a damp cloth. Don't forget to replace the cap before you close dishwasher door.

ATTENTION! Clean up any rinse aid split during filling with an absorbent cloth to avoid excess foaming during the next wash.

Page 16 Page 9