ADDITIONAL SAFETY RULES FOR

TABLE SAW

WARNING: FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.

1.DO NOT OPERATE THIS MACHINE until it is assembled and installed according to the instructions.

2.OBTAIN ADVICE FROM YOUR SUPERVISOR, instructor, or another qualified person if you are not familiar with the operation of this machine.

3.FOLLOW ALL WIRING CODES and recommended electrical connections.

4.USE THE GUARDS WHENEVER POSSIBLE. Check to see that they are in place, secured, and working correctly.

5.AVOID KICKBACK by:

A.keeping blade sharp and free of rust and pitch.

B.keeping rip fence parallel to the saw blade.

C.using saw blade guard and spreader for every possible operation, including all through sawing.

D.pushing the workpiece past the saw blade prior to release.

E.never ripping a workpiece that is twisted or warped, or does not have a straight edge to guide along the fence.

F.using feather boards when the anti-kickback device cannot be used.

G.never sawing a large workpiece that cannot be controlled.

H.never using the fence as a guide when crosscutting.

I.never sawing a workpiece with loose knots or other flaws.

6.ALWAYS USE GUARDS, SPLITTER, AND ANTI- KICKBACK FINGERS except when otherwise directed in the manual.

7.REMOVE CUT-OFF PIECES AND SCRAPS from the table before starting the saw. The vibration of the machine may cause them to move into the saw blade and be thrown out. After cutting, turn the machine off. When the blade has come to a complete stop, remove all debris.

8.NEVER START THE MACHINE with the workpiece against the blade.

9.HOLD THE WORKPIECE FIRMLY against the miter gauge or fence.

10.NEVER run the workpiece between the fence and a moulding cutterhead.

11.NEVER perform “free-hand” operations. Use either the fence or miter gauge to position and guide the workpiece.

12.USE PUSH STICK(S) for ripping a narrow workpiece.

13.AVOID AWKWARD OPERATIONS AND HAND POSITIONS where a sudden slip could cause a hand to move into the blade.

14.KEEP ARMS, HANDS, AND FINGERS away from the blade.

15.NEVER have any part of your body in line with the path of the saw blade.

16.NEVER REACH AROUND or over the saw blade.

17.NEVER attempt to free a stalled saw blade without first turning the machine “OFF”.

18.PROPERLY SUPPORT LONG OR WIDE workpieces.

19.NEVER PERFORM LAYOUT, assembly or set-up work on the table/work area when the machine is running.

20.TURN THE MACHINE “OFF” AND DISCONNECT THE MACHINE from the power source before installing or removing accessories, before adjusting or changing set-ups, or when making repairs.

21.TURN THE MACHINE “OFF”, disconnect the machine from the power source, and clean the table/work area before leaving the machine. LOCK THE SWITCH IN THE “OFF” POSITION to prevent unauthorized use.

22.ADDITIONAL INFORMATION regarding the safe and proper operation of this tool is available from the Power Tool Institute, 1300 Summer Avenue, Cleveland, OH 44115-2851. Information is also available from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201. Please refer to the American National Standards Institute ANSI 01.1 Safety Requirements for Woodworking Machines and the U.S. Department of Labor OSHA 1910.213 Regulations.

SAVE THESE INSTRUCTIONS.

Refer to them often

and use them to instruct others.

3

Page 2 Page 4
Page 3
Image 3
Delta 36-550, 36-560 w/stand) Refer to them often Use them to instruct others, Additional Safety Rules for Table SAW
Page 2 Page 4

36-560 w/stand), 36-550 specifications

The Delta 36-550 and Delta 36-560 are versatile table saws designed for both amateur woodworkers and seasoned professionals. These tools stand out in the market due to their robust features, reliability, and precision cutting capabilities.

One of the prominent features of the Delta 36-550 and 36-560 is their powerful motor. Both models are equipped with a 15-amp motor that provides ample power to handle a variety of wood types, from softwoods to hard species. This makes them suitable for a wide range of cutting applications, whether for general woodworking projects or more intricate tasks.

Both models come with a 10-inch blade diameter, allowing for significant cutting depth and width. The 36-550 offers a maximum cutting depth of 3-1/8 inches at 90 degrees and 2-1/4 inches at 45 degrees, while the 36-560 matches these specifications, ensuring that users have ample capacity for various wood thicknesses.

The precision fence system is another noteworthy characteristic. The exclusive Delta T2 tool-free fence system ensures smooth operation and accuracy, allowing woodworkers to make straight, clean cuts consistently. The fence is easy to adjust and locks securely, providing confidence during operation.

Safety is a crucial factor in woodworking, and both models incorporate several features to protect users. The blade guard system is transparent, allowing for visibility during cuts while providing necessary protection. Furthermore, the onboard storage for accessories, as well as a sturdy table design, facilitates a tidy workspace.

Both the Delta 36-550 and 36-560 come equipped with a heavy-duty steel stand, ensuring stability during use. The stand is designed for easy setup and provides a solid base, significantly reducing vibrations during operation. This characteristic enhances safety and improves overall cutting precision.

Additionally, both saws feature a dust port that connects to a vacuum system, promoting a clean working environment. Reducing dust not only keeps the workspace tidy but also improves visibility and safety during cutting operations.

In summary, the Delta 36-550 and 36-560 table saws combine power, precision, and safety into a robust package ideal for any woodworking enthusiast. With features like a reliable motor, precise fence system, enhanced safety protocols, and sturdy construction, these table saws stand out as excellent choices for anyone looking to elevate their woodworking projects.
Top Page Image Contents