Air Filter - Inspection and Replacement

Hot surfaces. Risk of burn.

Compressor heads are exposed when filter cover is removed. Allow compressor to cool prior to servicing.

A dirty air filter will not allow the compressor to operate at full capaci- ty. Keep the air filter clean at all times.

1.Remove the air filter cover.

2.Remove the air filter from filter cover.

IMPORTANT: Do not operate the compressor with the air filter removed.

3.Place new air filter into filter cover. Refer to the "Repair Parts" for the correct part number.

4.Replace air filter cover and lock into place.

Belt - Replacement

(Refer to the Outfit Parts Manual for replacement belt part number.)

Serious injury or damage may

occur if parts of the body or loose items get caught in moving parts. Never operate the outfit with the belt guard removed. The belt guard should be removed only when the AIR compressor power is disconnected.

1.Turn air compressor off, lock out the power supply, and relieve all air pressure from the air tank.

2.Remove the belt guard.

3.Mark pump position on saddle.

4.Loosen the motor mounting screws and slide the motor toward the air compressor.

5.Remove the belt and replace with a new one.

6.See the "Adjust Belt Tension" before tightening motor mount- ing screws.

Adjusting Belt Tension

1.Slide motor into original position, line the motor up with the mark made earlier on saddle.

2.Tighten two outside motor mounting screws enough to hold the motor in place for checking pulley and flywheel alignment.

3.The belt should deflect 3/16" at midway between the pulley and the flywheel when a 5 pound weight is applied at the midway point.

Deflection

4.When proper belt tension is achieved, tighten all four motor mounting screws. See Parts manual for torque specifications.

NOTE: Once the engine pulley has been moved from its factory set loca- tion, the grooves of the flywheel and pulley must be aligned to within 1/16" to prevent excessive belt wear. Verify the alignment by performing the fol- lowing Pulley and Flywheel - Alignment.

D25235

18-ENG

Page 17 Page 19
Page 18
Image 18
Delta D25235 029-2, DLKC6580V2 Air Filter Inspection and Replacement, Belt Replacement, Adjusting Belt Tension
Page 17 Page 19

D25235 029-2, DLKC6580V2 specifications

Delta DLKC6580V2 and D25235 029-2 represent significant advancements in the realm of industrial automation and control systems. These products harness cutting-edge technology to enhance operational efficiency, reliability, and flexibility across various applications.

The Delta DLKC6580V2 is a highly versatile motion control system designed for precision and performance. It boasts a robust architecture that supports a wide range of servo motors, making it ideal for applications requiring fine-tuned movements. One of the standout features of the DLKC6580V2 is its advanced control algorithms, which enable smooth and accurate motion, minimizing vibrations and ensuring high-quality outputs. Additionally, its real-time processing capabilities allow for rapid response and adjustments during operation, which is crucial in high-speed manufacturing environments.

Another key feature of the DLKC6580V2 is its integrated communication options. It supports multiple industrial protocols, including EtherCAT and CANopen, allowing seamless integration with various controllers and devices within an industrial setup. This flexibility enhances the overall system configuration and reduces downtime during installation and maintenance.

On the other hand, the D25235 029-2 is an innovative industrial power supply unit known for its reliability and efficiency. The D25235 series is designed to provide stable power under varying load conditions, making it an essential component for uninterrupted operations in critical applications. Its high efficiency minimizes energy consumption, contributing to lower operational costs and a reduced carbon footprint.

The D25235 029-2 features advanced protection mechanisms that safeguard against surges, overloads, and short circuits, ensuring long-term durability and reliability. The compact design of the unit also facilitates easy integration into existing systems, providing users with considerable versatility in installation.

Both the DLKC6580V2 and D25235 029-2 excel in delivering user-friendly interfaces, simplifying operation and configuration. With intuitive software tools, operators can quickly set up, monitor, and adjust settings, enhancing overall productivity.

In conclusion, Delta’s DLKC6580V2 and D25235 029-2 represent the pinnacle of innovation in industrial control and power supply systems. Their advanced features, exceptional performance, and robust technologies make them indispensable tools for modern manufacturing processes, offering businesses the ability to achieve higher efficiency and reliability in their operations.
Top Page Image Contents