Delta Electronics CTA instruction sheet Precaution, Parameters in Configuration Mode

2006-12-08

5011646001-CTE1

Instruction Sheet

Thank you very much for purchasing DELTA CTA series. Please read this instruction sheet before using your CTA series to ensure proper operation and please keep this instruction sheet handy for quick reference.

¾DANGER! Caution! Electric Shock!

¾ When the power is on, DO NOT touch the AC terminals in case an electric shock may occur.

¾Make sure the power is disconnected when you check the unit inside.

¾CTA series is an OPEN-TYPE device. They are intended for installation completely within an overall panel and are for use

in counting or timing application. If it will cause serious injury to workers or damage on other equipments when used in a dangerous environment, please make sure it is installed in an automatic safety protection device.

1. Precaution

1.Always use recommended solder-less terminals: Fork terminal with isolation (M3 screw, width 7.0mm), hole (diameter

3.2mm). Screw size: M3x6.5 (with 6.8x6.8 square washer). Recommended tightening torque: 0.4 N.m (4kgf.cm).

Applicable wire: solid/twisted wire of 2mm2, 12AWG to 24 AWG. Please be sure to tighten them properly.

2.Prevent dust or metallic debris from falling into the device and cause malfunctions.

3.DO NOT modify or uninstall the device.

4.DO NOT use empty terminals.

5.Make sure the wires are correctly connected to proper terminals.

6.Keep away from high-voltage and high-frequency environment during installation in case of interference.

7.Prevent using the device in premises which contain:

․Dust or corrosive gas ․High humidity ․High radiation ․Vibration and shock

8.	CTA series is an open-type device. Make sure to install it in an enclosure to prevent dust, humidity in case of an electric
	shock.
9.	Please make sure the power cables and signal device are installed correctly before switching on the power; otherwise
	serious damage may occur.。
10.	DO NOT touch the terminals or repair the device when the power is on; otherwise an electric shock may occur.
11.	Please wait for one minute after the power is switched off to allow the capacitor to discharge and DO NOT touch the
	internal wiring within this period.
12.	Use dry cloth to clean the device. DO NOT use acid or alkaline liquid to clean the device.

4. Specification Power signal Power signal

Power input

AC 100~240V, 50/60Hz

Start signal

Start signal

Input voltage range

85% to 110%, rated voltage

Pause signal

Pause signal

Power consumption

Less than 10VA

Clear signal

Clear signal

External power supply

12Vdc ±10%, 100mA

Output signal

t

t

Output signal

t

t

Display

Double-line, 6-digit negative transmissive LCD display

SV

SV

Non-voltage input (NPN): ON impedance 1K ohm max. ON residual voltage: 2V max.

Input signal

Up

Up

0

Voltage input (PNP): High level: 4.5 to 30Vdc, Low level: 0 to 2Vdc

0

SV

SV

Output 1

Relay: SPST max.250Vac, 5A (resistance load)

Down

Down

0

0

Transistor: NPN open collector. When 100mA /30Vdc, residual voltage=1.5Vdc max.

Signal On Delay 1

Signal On Delay 2

Output 2

Relay: SPDT max.250Vac, 5A (resistance load)

Transistor: NPN open collector. When 100mA /30Vdc, residual voltage=1.5Vdc max.

Power signal

Power signal

Dielectric strength

2000Vac 50/60 Hz for 1 minute

Vibration resistance

Without damage: 10~55Hz, amplitude=0.75mm, 3 axes for 2 hours

Start signal

Start signal

Shock resistance

Without damage: drop 4 times, 300m/s2, 3 edges, 6 surfaces and 1 corner

Ambient temperature

0 oC to +50 oC

Pause signal

Pause signal

Storage temperature

-20 oC to +65 oC

Clear signal

Clear signal

Altitude

2000m or less

Output signal

Ambient humidity

35% to 85% RH (non-condensing)

Output signal

SV

Pollution degree

Degree 2

SV

Up

Up

5. Parameters in Configuration Mode

0

0

Down

Down

SV

SV

™ Timer

0

0

Signal Off Delay

Signal On

Select a

Setup Timer

Select

Setup the

Setup the

Reset min.

Select input

Back to

Power signal

Power signal

function

function,

output

displayed

pulse width

pulse width

type (PNP

(counting up

mode of

unit of timer

of output 1

or NPN)

“select a

Start signal

Start signal

or down)

Timer

function”

Pause signal

Pause signal

MODE

MODE

MODE

MODE

MODE

MODE

MODE

Clear signal

Clear signal

™ Counter

Output signal

t

t

t

Output signal

t

t

t

t

SV

SV

Select a

Select

Setup input

Setup output

Setup dual

Setup counting

Setup the

Up

0

Up

0

function

counting

mode of

mode of

output counting

speed

pulse width of

SV

Down

SV

modes

Counter

Counter (not

mode (dual

output 1

Down

0

0

dual output)

output)

Power On Delay

Power On Delay Hold

MODE MODE MODE MODE MODE MODE MODE

2. Display, Indicators and Keys

Back to	Select input	Reset min.
	type (PNP or	pulse width
“select a
	NPN)
function”
	MODE	MODE

Save data or	Setup pre-scale	Setup the	Setup the
not while	value	decimal point	pulse width of
switching off			output 2
power
MODE	MODE	MODE	MODE

Power signal Power signal

Start signal	Start signal
Pause signal	Pause signal

Reset 2 indicator Reset 1 indicator Key protect 2 indicator

Key protect 1 indicator

Output 2 indicator Output 1 indicator

Special function indicator

Lock key

Reset key

Mode and number shift key

PV(Present Value) display

SV(Set Value) display

Timer function indicator Counter function indicator Tachometer function indicator

Up/Down key

™Tachometer

Select a function	Setup output mode
	of Tachometer
MODE	MODE
Back to “select a	Select input type
	(PNP or NPN)
function”

MODE

Setup counting	Setup the decimal	Setup pre-scale value
speed	point
MODE	MODE	MODE
Reset min. pulse	!	Setup the delay time
	Setup the average of
width	input data	while switching on
		power
MODE	MODE	MODE

Clear signal			Clear signal
			Output signal	t	t		t
Output signal
SV			SV
Up			Up
0			SV
SV
Down			Down
0
	Repeat Cycle	timer output set as 0		Repeat Cycle		timer output not set as 0

Power signal Power signal

Start signal Start signal

™Timer + Counter Mixed

Pause signal Pause signal

RST 1/2	Light on when reset signal is detected	BATCH	“Batch Counting Mode” in Counter and Tachometer function
K/P 1/2	Light on when key-protected mode is enabled SET 1 2		SV1, SV2 display
OUT 1/2	Light on when output is executing	TAC	Light on when Tachometer function is executing
H M S	Hour, minute, second, unit of timer, displayed	CNT	Light on when Counter function is executing
TOTAL	in Timer function
	“Total Counting Mode” in Counter and	TMR	Light on when Timer function is executing
	Tachometer function

™Key Operation

			Increase and decrease SV or change parameter settings.
			Left move 1 digit of the selected digit. The indicator of the selected digit will flash.
	MODE		Save the set parameters or switch among functions.
	LOCK	Prevent settings from being changed. Key-protected mode still works after the power is switched off. Press
				to enter key-protected mode. In non-key-protected status, press			to enter Lock 1. In Lock 1, press
			LOCK			LOCK
				again to enter Lock 2. Press MODE and at the same time to disable key-protected mode.					(Lock 1)
			LOCK
			disables the functions of all keys.		(Lock 2) allows users to change SV and functions of				remain.
								RESET
				only functions in non-key-protected status.
			LOCK
RESET			Clear	and reset PV.

™Modes: Operation Mode and Configuration Mode

Operation	When the power is on, the timer/counter/tachometer is in the operation mode. Press							to change SV, or
	to make change on a desired digit. The indicator of the selected digit will flash. After the change is made,
	press MODE to save the setting. If SV or parameters are not changed, press MODE once to switch between SET1 and
Configuration	SET2.
	Press MODE in operation mode for more than 3 seconds to enter configuration mode. Press MODE once to switch
	among parameters. To return to operation mode, press MODE for more than 3 seconds.
3. Ordering Information
	CTA
	1	2	3	4	5	6
n Product name CTA: Delta Counter/Timer/Tachometer A series					q Preset stage		0: 2 preset stage
o Panel size	4: 48mm x 48mm 1/16DIN				r Communication 0: none
p Output 2	0: NPN; 1: Relay				s Power supply		A: AC 100~240V

Clear signal

Clear signal

Select a

Setup Timer

Setup

Setup the

Setup

Setup

Setup

Setup the

Output signal

t

t

t

Output signal

function

function,

output

displayed

input

output

counting

pulse width

SV

SV

(counting

mode of

unit of

mode of

mode of

speed

of output 1

Up

Up

0

0

up or down)

timer

timer

Counter

Counter (not

SV

SV

dual output)

Down

Down

0

MODE

MODE

MODE

MODE

MODE

MODE

MODE

0

MODE

RCYH timer output not set as 0

Repeat Cycle Hold

Timer output set as 0

Back to	Select		Reset	Save data	Setup	Setup	Setup the	Power signal		Power signal
	input type		min.	or not	pre-scale	the	pulse
“select a	(PNP or		pulse	while	value	decimal	width of	Start signal		Start signal
function”	NPN)		width	switching		point	output 2
				off power				Pause signal		Pause signal
	MODE		MODE	MODE	MODE	MODE	MODE			Clear signal
6. Timer Function								Clear signal
									SV1		SV
								Output signal		Output signal
There are counting up/down modes, several counting units and output modes to choose from in timer function.								Up	SV2		Up
									0		0
									SV1		SV
	Select counting up			or counting down				Down	SV2	Down
									0		0
	Setup the output time of timer, from 0 to 99.99 secs. 0= Hold output									Repeat Cycle 2	Signal Cumulate
	Setup output modes
								Power signal		Power signal
Setup the counting unit of the timer.
sec		0.01~9999.99		A unit = 10ms.	Max. counting = 9999.99 secs.			Start signal		Start signal
sec			0.1~99999.9	A unit = 0.1sec.	Max. counting = 99999.9 secs.					Pause signal
sec			1~999999	A unit = 1 sec.	Max. counting = 999999 secs.			Pause signal
min,sec		0.01~9959.99		A unit = 0.01 sec.	Max. counting = 5999.99 secs.			Clear signal		Clear signal
min,sec			0.1~99959.9	A unit = 0.1 sec.	Max. counting = 59999.9 secs.			Output signal		Output signal
min			0.1~99999.9	A unit = 0.1 min.	Max. counting = 99999.9 mins.
									SV1		SV1
min			1~999999	A unit = 1 min.	Max. counting = 999999 mins.
								Up	SV2	Up	SV2
hr,min,sec			1~995959	A unit = 1 sec.	Max. counting = 359999 secs (100hr)				0		0
									SV1		SV1
hr,min			1~999959	A unit = 1 min.	Max. counting = 35999999 secs (10000hr)			Down
									SV2	Down
											SV2
hr			1~999999	A unit = 1 hr.	Max. counting = 999999 hrs				0	Signal Twin ON-Start	0
											Signal Twin OFF-Start