Delta Electronics DVP-Slim instruction sheet X Introduction, Y Specifications, Model Information

2007-01-23

http://www.delta.com.tw/industrialautomation/ 5011658300-MNE0

Digital I/O Extension Unit

(Pin Headed)

Instruction Sheet

Warning

3Please read this instruction sheet carefully before use.

3DVP-Slim is an OPEN-TYPE device and therefore should be installed in an enclosure free of airborne dust, humidity, electri shock and vibration. The enclosure should prevent non-maintenance staff from operating the device (e.g. key or specific tools are required to open the enclosure) in case danger and damage on the device may occur.

3DO NOT connect input AC power supply to any of the I/O terminals; otherwise serious damage may occur. Check all the wiring again before switching on the power. DO NOT touch any terminal when the power is switched on.

XIntroduction

1.1 Model Explanation & Peripherals

Thank you for choosing Delta DVP-Slim series programmable logic controller. DVP-Slim series pin-headed digital I/O extension unit offers 32 points. For DVP-SS/SA/SX/SC series MPU, the maximum digital I/O extension points (including the MPU) can reach 128 points. For SV series MPU, the maximum digial I/O extension points (including the MPU) can reach 256 points. In addition, maximum 8 additional special modules (AD/DA/PT/TC/XA/PU) can be extended to DVP-Slim series extension unit.

Nameplate Explanation

Delta PLC model name
Power input spec.		24Vdc 1W
Output point module spec.		0.1A(24VDC)POINT
Barcode & serial No.
Version	VX.XXAX	32SN11TNT7020001

		M A D E I N X X X X X
Model Name		Serial No.
DVP series
Points (32 for output)	TN: NPN transistor	Production No.
Module type	N: No output module	Production week
		Production year (2007)
M: Input point extension unit
		Production plant
N: Output point extension unit	DC power input
		Model name

1.3	Model Information
Model name		Power		Input		Output	Dimension	Outline
		supply	Points	Type	Points	Type	(mm)

DVP32SM11N		32	DC Type	0	N/A
			Sink/Source
	24V DC					25.2	90	60
DVP32SN11TN		0	N/A	32	(NPN)
					Transistor

YSpecifications

2.1 Electrical Specifications

Model	DVP32SM11N	DVP32SN11TN
Item
Power supply voltage	24V DC (-15% ~ 20%) (with DC input polarity reverse protection)
Motion specification	Within 5ms of the momentary power loss, the device will keep on operating.
Power consumption	1W	1.5W
Insulation resistance	＞5 MΩ (all I/O point-to-ground: 500V DC)
	ESD (IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge
	EFT (IEC 61131-2, IEC 61000-4-4): Power Line: 2KV, Digital I/O: 1KV,
Noise immunity	Analog & Communication I/O: 1KV
	Damped-Oscillatory Wave: Power Line: 1KV, Digital I/O: 1KV
	RS (IEC 61131-2, IEC 61000-4-3): 26MHz ~ 1GHz, 10V/m
	The diameter of grounding wire shall not be less than that of L, N terminal of the
Earth	power. (When many PLCs are in use at the same time, please make sure every PLC
	is properly grounded.)
Operation/storage	Operation: 0ºC ~ 55ºC (temperature); 50 ~ 95% (humidity); pollution degree 2
environment	Storage: -40ºC ~ 70ºC (temperature); 5 ~ 95% (humidity)
Shock/vibration	International standards: IEC1131-2, IEC 68-2-6 (TEST Fc)/IEC1131-2 & IEC 68-2-27
immunity	(TEST Ea)
Weight (g)	70g	70g

2.2 I/O Point Specifications

		Input Point
Input type	DC (SINK or SOURCE)
Input current	24VDC, 5mA
Active level	Off Æ On	more than 16V DC
	On Æ Off	less than 14.4V DC
Response time	Approx. 10ms, 0 ~ 15ms adjustable from D1020, D1021
Circuit isolation /	By photocoupler / LED On
operation instruction

ƒDVP32SN currently only offers TN (NPN) transistor output.

ƒPlease be aware of the following PIN wiring methods for DVP32SN to prevent burn-down of the extension unit.

1.PIN19, PIN20, PIN39 and PIN40 can only connected to +24V DC. The 4 points have already been designed as short-circuit within the extension unit; therefore only 1 of the points needs to be wired.

2.PIN17, PIN18, PIN37 and PIN38 can only connected to GND. The 4 points have already been designed as short-circuit within the extension unit; therefore only 1 of the points needs to be wired.

3.2 Connection

Step 1: Screw open the side cover of the extension unit and you will see the connection port.

Step 2: Lift the fixing clip by the screwdriver.

Step 3: Adjust the positioning hole of the MPU and the extension unit and meet the connection port on the MPU with the extension unit to tightly connect the two.

Step 4: Fasten the fixing clip on the extension unit to complete the connection.

1.2 Product Profile

		Output Point
Output type	Transistor – T (NPN)
Current specification	0.1A/point
Voltage specification	5 ~ 24 VDC
Maximum load	55ºC/1A (COM), 25ºC/2.4A (COM)
Response time	Off Æ On	less than 0.1ms
	On Æ Off	less than 0.3ms

Unit: mm

c POWER, L.V (low voltage) indicator	h Extension unit positioning hole
d Model name	i Nameplate
e Extension unit fixing clip	j Extension unit fixing clip
f I/O terminals	k DIN rail (35mm)
g DIN rail clip	• Connection port for extension unit

ZInstallation & Wiring

3.1 Terminals of Digital I/O Extension Unit

DVP32SM11N

X0	1	2	X1
X2	3	4	X3
X4	5	6	X5
X6	7	8	X7
X10	9	10	X11
X12	11	12	X13
X14	13	14	X15
X16	15	16	X17
S/S	17	18	S/S
NC	19	20	NC
X20	21	22	X21
X22	23	24	X23
X24	25	26	X25
X26	27	28	X27
X30	29	30	X31
X32	31	32	X33
X34	33	34	X35
X36	35	36	X37
S/S	37	38	S/S
NC	39	40	NC

DVP32SN11TN

Y0	1	2	Y1
Y2	3	4	Y3
Y4	5	6	Y5
Y6	7	8	Y7
Y10	9	10	Y11
Y12	11	12	Y13
Y14	13	14	Y15
Y16	15	16	Y17
GND	17	18	GND
+24V	19	20	+24V
Y20	21	22	Y21
Y22	23	24	Y23
Y24	25	26	Y25
Y26	27	28	Y27
Y30	29	30	Y31
Y32	31	32	Y33
Y34	33	34	Y35
Y36	35	36	Y37
GND	37	38	GND
+24V	39	40	+24V

3.3 Installation & Wiring

Install the PLC in an enclosure with sufficient space around it to allow heat dissipation as shown in the figure below.

D

DDVP D MPU

D

D > 50mm

DVP32SM DVP32SN