Delta Electronics TP04G-AS2 specifications 警示指示燈, ，最大可顯示, 數值鍵及功能鍵, 注意事項, Hardware Operation, 產品簡介

Panel component Explanation

Function keys

F3/F8: It is used to be constant 3 (F3) and 8 (Shift+F3) when it is in the system menu, the user can use it to define functions separately when they are in user page.

F4/F9: It is used to be constant 4 (F4) and 9 (Shift+F4) when it is in the system menu, the user can use it to define functions separately when they are in user page.

注意事項

￿

￿

￿

￿Back Panel

1.If the user forgot the password, the password can be cleared by using the following code: . This universal code will clear the password and all TP04 series internal programs. The TP04 series will be reset to the factory settings by using this code also. Please pay close attention when using it.

2.The password can be the alphabet from A to Z or the number from 0 to 9. But it must use the function keys F0 ~ F9 to input the password characters. Please refer to the following table.

F0/F5: Scrolls in a loop as follows 0→5→A→B→C→D→E→F→0

F1/F6: Scrolls in a loop as follows 1→6→G→H→I→J→K→1

BATTERY

SWITCH OR

RS-485/422

F2/F7: Scrolls in a loop as follows 2→7→L→M→N→O→P→2

F3/F8: Scrolls in a loop as follows 3→8→Q→R→S→T→U→V→3

F4/F9: Scrolls in a loop as follows 4→9→W→X→Y→Z→4

￿Hardware Operation

5 PIN terminal/Wire gauge: 12-24 AWG/Torque: 4.5 lb.-inch

￿Dimension

When the user wants to startup TP04 series, a 24V DC power is needed. After applying 24V DC power to TP04 series, it will enter into the startup display and then enter the user-designed program. Pressing Esc key and holding on for 5 seconds can return to system menu. There are five selections in the system menu and are described below.

Front panel (unit: mm [inch])	Right side diagram (unit: mm [inch])
97.00	85.00
[3.82]
	[3.35]
147.00 [5.79]
Mounting dimension (unit: mm [inch])	Vertical view (unit: mm)

85

[3.35]

135~136.5[5.31~5.37]

Thickness Range 0.5~9mm

￿Installation

Please insert TP04 series to the opening hole of panel and tighten the screws. However, if a firm mounting TP04 series to the panel is needed, please use the mounting fixed support accessory which is packed together with TP04 series, then insert the fixed support in the back and tighten the screws.

If the fixed support is not installed well, Delta will not guarantee the waterproof function. The screw torque should be 4-5(kg-cm). DO NOT exceed this specification when tightening the screws; otherwise TP04 series may be damaged.

Notes: The flat surface should be a UL Type 4 "Indoor Use Only" enclosure or equivalent (IP65/NEMA4). Please refer to the figures below.

Pl ease leave suffi cient space (mor e than 50mm ) ar ound the unit for heat dissipation.

Thickness: 0.5~9.0mm

	本機顯示操作面板防水，但對油污或具腐蝕性之液體不具防護作用，避免以尖銳之物品刮傷面板使用時請注
￿				24V	RS-485
						通訊口信號端，否則可能造成嚴重的損壞，因此請在上電之前
￿
￿
￿
￿
￿		產品簡介
	￿				TP04G-AS2			128*64		8*4
	請在使用之前，詳細閱讀本使用說明書。									個中文字，支援多國
	實施配線，務必關閉電源。
	意。		為直流	，不可連 於
		輸入
	再次確認電源配線。							在上電時觸摸任何端子
	輸入電源切斷後，一分鐘之內，請勿觸摸內部電路。
		體上之接地端子		務必正確的接地，可提高產品抗雜訊能力。					。
							請勿

Selections

Download program

Upload program

Copy program

TP04 settings

PLC connection

Execution

Explanation

Use the connection cable (DVPACAB530) to connect the TP04 serial communication port RS-232 to a PC. Then use the TPEditor software to download an application program to TP04.

Use the connection cable (DVPACAB530) to connect the TP04 serial communication port RS-232 to a PC. Then use the TPEditor software to upload an application program from TP04.

Transfer a program between two TP04 units. 1: transmit programs. 2: receive programs

When transmit programs and data between two TP04 units. Set one TP04 to “Receive Program” mode and the other TP04 to “Transmit Program” mode. Please use twisted pair wires to connect the two units via the RS-485 ports.

There are 9 items that used to modify TP04 system settings:

1.Communication protocol: Setting the address of TP04, the control port of PLC, and the communication string for either RS-232 or RS-485.

2.Contrast: Adjust the contrast of LCM display screen.

3.Back-light: adjust the automatic turn off time of LCM. Setting range is 00 ~ 99 minutes. If set to 00, the LCM Back-light will not turn off.

4.Date and Time: It is used to set the TP04 built-in RTC including year, month, day, hour, minute, second and week. Also the internal battery capacity display is shown here.

5.Buzzer: Used to set the buzzer sound, normal mode or quiet mode.

6.Language Setting: Used to set the displayed language. English, Traditional Chinese, Simplified Chinese or user defined language.

7.Password setting: Used to set, enable, and disable the password function. If the password

function is enabled, it will require the user to input a password before entering any system menu.

The factory password is .

8.Startup display: Used to select the TP04 startup display. User can select “user defined” to use the file that designed by TPEditor and download to TP04.

9.Comm. indicator: The user can determine if the RS-232 and RS-485 LEDs will blink or not during communication.

There are three methods to connect to PLC:

1.Using TP04 serial communication port (COM1) RS-232: set 8-pin DIP switch to RS-485 mode and connect the cable (DVPACAB215 or DVPACAB230) to program communication I/O RS-232C of PLC.

2.Using extension communication port (COM2): set 8-pin DIP switch to RS-485 mode and connect 5-pin removal terminal of extension communication port to RS-485 of PLC with twisted pair.

3.Using extension communication port (COM2): set 8-pin DIP switch to RS-422 mode and connect four pins (6, 7, 8, 9) of 9 PIN D-SUB male to RS-422 of PLC with 4-wire cable.

Execute the internal program that download from TPEditor or transmitted from other TP04 units. When program is in execution, the user can return to system menu by pressing Escape/Exit (Esc) key for 5 seconds.

￿

(RS-232

RS-485/RS-422

)

￿

/

LED

￿

￿

￿

利用原廠包裝附件之固定L架C M，鎖緊面板固定螺絲時，

R S-2 32

太緊以免造成機殼損壞R S-4 8 5

型號說明

/

警示指示燈

複合功能

，解析度

，最大可顯示

謝謝您採用台達終端顯示器系列產品。

￿

文字顯示。

及

，可同時使用

兩個通訊口

。

萬年曆、通訊 警告指示

可外接程式複製單元，快速移植程式，節省程式下載時間。

(

)

狀態一：當啟動電源時，指示燈慢慢開始閃爍。

內建多種物件圖形可供使用者選用。

RS-232

( )

RS-232

RS-產品外觀及各部介紹485/RS-422( )

RS-485/RS-422

LCM

/

UP/Pg Up

顯示區

Pg Dn/DOWN

Left

退出 取消

Right

鍵

輸入

面版功能說明

F0 ~ F9

數值鍵及功能鍵

F0/F5

0 (F0)

5 (Shift+F0)

的常數輸入鍵，在使用者頁面時可

面板元件

F1/F6

1 (F1)

6 (Shift+F1)

說明

警示指示燈 紅燈

二

異常狀態發生，指示燈會重覆持續亮一秒並發出警報聲。

指示燈 黃燈

綠燈

傳送程式及使用

通訊時持續閃爍。

顯示區

指示燈

使用

通訊時持續閃爍。

液晶顯示模組，顯示目前程式狀態。

退出 取消鍵

進入系統選單或輸入值錯誤時可按此鍵，刪除文字敘述等。

命令操作

：此鍵為 上方向鍵，可作為數值遞增輸入或換至上頁等操作。

：此鍵為向下方向鍵，可作為數值遞減輸入或換至下頁等操作。

：此鍵為左方向鍵，可作為選擇數值位置操作。

複合功能鍵

此鍵為右方向鍵。可作為選擇數值位置操作。

此鍵是搭配功能鍵

及其他按鍵作為特殊功能的使用。

Warning ENGLISH

￿Please read this instruction carefully before use.

￿Switch off the power before wiring.

￿The display panel of TP04 series is waterproof. But please prevent grease, corrosive liquids and sharp objects from contacting the TP04 series.

￿The TP04 series require 24VDC input power. DO NOT connect input AC power supply to any of the RS-485 communication port; otherwise serious damage may occur. Check all the wiring again before switching on the power.

￿DO NOT touch any terminal when the power is switched on. DO NOT touch any internal circuit in 1 minute after the power is switched off.

￿Make sure the groud terminal is correctly grounded in order to prevent electromagnetic interference.

￿Please use the fixed support accessory which is packed together with the product provided by Delta. DO NOT tighten the screws out of the normal torque specifications; otherwise serious damage may occur.

￿Introduction

￿Model Explanation

Thank you for choosing Delta TP Series. TP04G-AS2 has the features of high resolution 128×64 dots and is able to display 8×4 Chinese character. It provides multilingual display and two built-in communication ports, one is for RS-232/RS-422 and the other is for RS-485. RS-232 and RS-485 can be used simultaneously. Besides, it also supports built-in RTC, communication/alarm LED indicators. The user can purchase program copy card (optional) to copy settings and programs quickly and save download time. Regarding the editing software, there are various objects and images for the user’s requirements.

￿Product Outline

	Alarm LED Indicator
	RS-232 LED Indicator
Displaying Area	RS-485/RS422 LED Indicator

Arrow Keys

Escape / Exit Key

Enter Key

Shift Key

Function Keys

￿Panel Function Explanation

Panel component	Explanation
Alarm LED indicator	Status 1: When power is on, LED will start to blink slowly
(RED)	Status 2: When there is an abnormal situation, LED will blink quickly along with an alarm sound.
RS-232 LED	LED will blink when transmits program and communicates via RS-232.
indicator (yellow)
RS-485/RS-422 LED	LED will blink when communicates via RS-485/RS-422.
indicator (green)
Displaying area	Liquid Crystal Module display area. It is used to display current program status.
Escape/Exit key	It is used to cancel an incorrect input, or to exit a programming step.
Shift key	It is used to select function keys F0 ~ F9 and other keys for special function.
	UP/Pg Up: It is used to increase the value or move up one page.
Arrow keys	Pg Dn/DOWN: It is used to decrease the value or move down one page.
	Left: This key is left direction key and it can be used to select the position of the value.
	Right: This key is right direction key and it can be used to select the position of the value.
Enter key	It is used to input a value or accept a programming command.
	F0/F5: It is used to be constant 0 (F0) and 5 (Shift+F0) when it is in the system menu, the user
	can use it to define functions separately when they are in user page.
Function keys	F1/F6: It is used to be constant 1 (F1) and 6 (Shift+F1) when it is in the system menu, the user
	can use it to define functions separately when they are in user page.
	F2/F7: It is used to be constant 2 (F2) and 7 (Shift+F2) when it is in the system menu, the user
	can use it to define functions separately when they are in user page.

￿ Specifications

￿ Communication Connection

￿ Function Specifications

￿ TP04G may connect to a PC by using connection able DVPACAB515

Item

TP04G-AS2

PC or TP02 / 04G

PC COM Port

TP02 / 04G COM Port

TO PC (RS-2 32)

TO TP0 2 / 04G

9 PIN D-SUB female

9 PIN D-SUB female

Screen type

STN-LCD

9

5

1

6

Rx

2

3

Tx

Display color

Monochromatic

6

1

5

9

Tx

3

2

Rx

GND

5

5

GND

9 PIN D-SUB

The back-light automatic turn off time is 1 ~ 99 minutes (0 = DO NOT turn off)

9 PIN D-SUB

Backlight

(The back-light life is about 50 thousand hours at 25°C)

￿ TP04G may connect to a DVP-PLC by using connection cable DVPACAB215/DVPACAB230/

Resolution

128x64 dots

DVPACAB2A30

Display range

(W) x (H) = 72 x 40 (unit: mm); 3.00” (diagonal preferred)

1. DVPACAB215/DVPACAB230

PC / TP CO M Po rt

PLC CO M1 Port

Contrast adjustment

10 levels of adjustment

25 PIN D-SUB female

8 PIN MINI DIN

TO P C o r TP 02 / 04 G

Tx

2

4

Rx

2

1

ASCII: (Code page 850) Alphanumeric (including European characters)

13

TO P LC

Rx

3

5

Tx

5 4

3

25 P IN D -S UB

GND 7

8

G ND

8

6

Language/Font

Taiwan: (Big 5 codes) Traditional Chinese Fonts

4

1 ,2

5 V

7

M INI DIN TER MIN AL

5

China: (GB2324-80 codes) Simplified Chinese Fonts

14

1

6

Display

8

9

5

2 0

screen

5×8 dots

25 characters×8 rows

6

1

9 P IN D -SU B

PC / TP CO M P ort

PLC CO M1 Port

Display

8×8 dots

16 characters×8 rows

9 PIN D-SUB fe male

8 PIN MINI DIN

2. DVPACAB2A30

Tx

3

4

Rx

text

8×12 dots

16 characters×5 rows

2

1

Rx

2

5

Tx

5 4

3

TO P C o r TP 02 / 0 4G

GND 5

8

G ND

8

6

8×16 dots

16 characters×4 rows

TO P LC

7

1 ,2

5 V

7

9

5

8

Font Size

ASCII: 5×8, 8×8, 8×12, 8×16

6

1

1

MINI DIN TERMINAL

4

9 P IN D-SUB

6

1. Power on indication (Blink for three times); 2. Communication error alarm;

Alarm LED indicator (RED)

3. Special indication by user programming.

￿ The Pin definition of 9 PIN D-SUB

RS-232 LED indicator

It will blink when transmitting program and communicating by using RS-232.

1. RS-232

2. RS-422

(yellow)

RS-485/RS-422

TP 02 / 0 4G COM Po rt

TP 02 / 04G COM Port

It will blink when communicating by using RS-485/RS-422.

RS-232 9 PIN D- SUB male

RS-422 9 P IN D -S UB male

LED indicator (green)

3

Tx

6

Rx +

Program memory

256KB flash memory

2

Rx

7

Rx -

5

GND

8

Tx +

RAM of system

32K Byte

9

Tx -

Serial communication port

Unsynchronized transmission method: RS-232;

3. DVPACAB630 (RS-422)

Data length: 7 or 8 bits, Stop bits: 1 or 2 bits; Parity: None/Odd/Even;

RS-232 (COM1)

TP 02 / 04G COM Port

MIT SUBIS HI F X-P LC

Transmission speed: 9,600 bps ~ 115,200 bps; RS-232: 9 PIN D-SUB male.

COM1 Port RS -422

9 P IN D -S UB female

TO TP02 / 04G

8 PIN MINI DIN

TO PLC

Extension communication

Unsynchronized transmission method: RS-485 / RS-422; Data length: 7 or 8 bits;

5

Rx+

6

7

Tx+

2

1

External

9

port RS-422 (COM1)

Stop bits: 1 or 2 bits; Parity: None/Odd/Even; Transmission speed: 9,600 bps ~

6

1

MINI DIN TERMINAL

Rx -

7

4

Tx -

5

4

3

interface

115,200 bps; RS-422: 9 PIN D-SUB male; RS-485: 5 PIN removal terminal.

9 PIN D-SUB

Tx+

8

2

Rx+

8

6

RS-485 (COM2)

Tx -

9

1

Rx -

7

Extension interface

1. Update firmware version. 2. The slot for program copy card.

GND

5

3

S G

Battery cover

3V DC battery for HMI

￿ Switch between RS-422/RS-485 (by using 8-PIN DIP switch)

5 PIN removal terminal

Include 24V DC input and RS-485 communication input

￿ Electrical Specifications

8-PIN DIP switch

RS-485

RS-422

SW1 ~ SW4

On

Off

Specifications

TP04G-AS2

SW5 ~ SW8

Off

On

Communication interface

COM1: RS-232/RS422; COM2: RS-485.

￿ Battery Life and Precision of Calendar

Waterproof class of front panel

IP65/NEMA4

Operating temperature for hardware	0 ~ 50°C; 20 ~ 90% RH (non-condensing)		Timer
Storage temperature for hardware	-20 ~ 60°C
	5Hz f 9Hz = Continuous: 1.75mm/Occasional: 3.5mm
Vibration	≦＜	￿ Battery Life
	9Hz≦f 150Hz = Continuous: 0.5g/Occasional: 1.0g
Shock	15g peak, 11ms duration, half-sine, three shocks in each direction per axis,		Temperature (°C)	-20	0	20	60
	on 3 mutually perpendicular axes (total of 18 shocks)		Life (Year)	1.972	2.466	2.712	2.835
Radiated emission	CISPR11, Class A
		￿ Precision of Calendar Timer
Electrostatic discharge immunity	EN61000-4-2
Radiated immunity	EN61000-4-3	1. At 0°C/32°F, less than -117 seconds error per month.
Electrical fast transient	EN61000-4-4	2. At 25°C/77°F, less than 52 seconds error per month.
Weight/dimensions	0.24kg; 147×97×35.5mm (Width(W)×Height(H)×Deep(D))	3. At 55°C/131°F, less than -132 seconds error per month.
Cooling method	Natural air cooling

F2/F7

2 (F2)

7 (Shift+F2)

的常數輸入鍵，在使用者頁面時可

F3/F8

3 (F3)

8 (Shift+F3)

F4/F9

4 (F4)

9 (Shift+F4)

￿

當輸入值確認正確無誤

，即可按下此鍵。

輸入

功能鍵

：在系統選單操作時可作為

BATTERY

或

SWITCH OR

RS-485/422

面板元件

由使用者定義其個別功能。

說明

5 PIN

/

12-24 AWG /

4.5 lb.-inch

￿

：在系統選單操作時可作為

或

功能鍵

(

mm

[ ]

inch)

(

mm

[ ] inch)

背面介紹

由使用者定義其個別功能。

97.00

線徑：

85.00

[3.82]

[3.35]

147.00 [5.79]

(

mm [ ] inch)

(

mm)

85

端子座

扭力：

[3.35]

外觀尺寸

， ：

右側圖 單位：

， ：

正面圖 單位：

135~136.5[5.31~5.37]

0.5~9mm

￿

原廠包

(

)

附件之固定架，嵌入後4蓋-5(kg-四cm)端凹槽處固定，並上、下平均鎖緊面板固定，螺若絲要即固可定，更如牢下固圖，可再為正利確安用

嵌入開孔尺寸 單位：

， ：

Type 4

俯視圖 單位：

嵌入式 0.5~9.0mm

厚度:

注裝人機意：（安介：該面安裝隔板厚度：固方法定裝螺於的絲平控時制面請盤必以須的扭是方力要法：，適用請直接將人室機鎖內由緊使盤，用面請或的勿相正超等面過條直此件接範的放圍配入以電即免盤可破外壞殼。嵌入式）